What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

Is there association of SARS-CoV-2 infection rate with meteorological factors?

There are contradictory research papers about the correlation between meteorological parameters and incidence of COVID-19 in some countries worldwide. Is there correlation between the...

15 February 2021 5,806 2 View

Why does the band sizes on Agarose gel electrophoresis differ from the peaks at capillary electrophoresis?

14 February 2021 4,773 4 View

What is the general cyclic energy degradation factor for plain concrete at material level in stress strain curve?

Plain Concrete subjected to cyclic loading get reduction in its stiffness and strength with the every cycle of loading. What is ratio of energy enclosed in one hysteresis loop to adjacent...

10 February 2021 1,051 1 View

How to calculate the Boiling point for metals at high vapor pressure?

In our experiment, some metal surfaces are exposed to radiation heat under high vapor gas pressure. I would like to ask if there is any way to calculate the boiling point for metals under high...

31 January 2021 249 4 View

The Akaike information criterion of the random forest model ?

Please, how to calculate the number of model parameters of the random forest model to determine the Akaike Information Criterion (AIC) using this following expression: AIC = n * log(MSE) + 2 *...

27 January 2021 816 6 View

Suggest me some satellite image datasets used for crop yield estimation?

I have my synopsis presentation and i have to provide details about 2-3 datasets that I can use in my research. Topic is crops Yield estimation using satellite images. suggest me what I can write?...

13 January 2021 1,675 3 View

What test should I use after a significant factoriual ANOVA?

Dear Colleagues Several resources recommended following significant interaction ANOVA with a simple main effect analysis to break down and interpret the interaction. I am wondering if I can...

29 December 2020 8,316 4 View

In your opinion , What is the percentage of demand for accountants and the percentage of stagnation ?

in your opinion , What is the percentage of demand for accountants and the percentage of stagnation ?

24 December 2020 5,349 3 View

How can increase the follower and citations of my articles?

I am looking for increasing the citations and reading my articles around the world.

13 December 2020 7,074 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

Model Volume fraction and magnetic field applications of nanofluids in ANSYS?

Hi I am working recently on a project where I have to study how the thermal properties or heat transfer enhancement of nanofluids as the volume fraction changes, or if a magnetic field is applied...

22 February 2021 961 2 View