How we can inject failure percentage like 5% ,10% 15 % upto so on 25 % in cloudsim ?

04 April 2018 1 9K Report

How we can inject failure percentage like 5% ,10% 15 % upto so on 25 % in cloudsim ? Is the Failure injection Class support this type of failure injection phenomena ? If no ? then how it can b possible ?

Sasko Ristov

Maybe you can try DynamicCloudSim, it has more than 10 parameters to configure uncertainty, one of which was VM failure rate.

Badges
Science method

More Asmara Jadoon's questions See All

Checkpointing fault tolerance technique record the system state periodically after certain time limit ? or After certain processing limit ?

Check pointing fault tolerance technique record the system state periodically after certain time limit ? or After certain processing limit ? If it store after certain time limit then what limit is...

03 April 2018 9,297 2 View

How to compare my fault tolerance techniques with the existing fault tolerance techniques using the throughput parameter?

I want to compare my fault tolerance techniques with the existing fault tolerance techniques using the throughput parameter..how can i compare the proposed and existing techniques like retry,...

02 March 2018 6,987 2 View

Whats is meant by predicted margin in weka ?

Weka gave predicted margin as well as predicted status. whats is this predicted margin?

11 December 2017 5,290 5 View

how we can predict the failure of job in cloud computing ?

can anyone suggest me good journal on the "Prediction of job failure " in cloud computing .

10 November 2017 1,593 0 View

How job failure can be predicted by using naive bayes technique?

I have a data set of the jobs in which success and failure rate of the task are also included.How we can predict the failures by using naive bayes technique. What will be our test set?

10 November 2017 2,252 0 View

What is your perception on using visual analysis or quantitative approaches to evaluate data from single-case research designs (n of 1 trials)?

Results of single-case research designs (i.e., n-of-1 trials) are often evaluated by visually inspecting the time-series graph and computing quantitative indices. A question our research team is...

03 March 2021 687 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

How can misfit between business requirents and ERP system business process be reduced?

One main reason for failure of most ERP implementations is the misfit between business requirents and ERP system business process be reduced. How can the misfit between business requirents and ERP...

22 February 2021 5,709 5 View

How can we add reinforced thermoplastics with granules in injection molding machine?

I need to make an injection molding machine in which short fibers are to be introduced. Short fiber length and material properties are to be determined and also the material strength are to be...

22 February 2021 4,290 1 View

Where can the fault diagnosis data set of lithium battery be found?

Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...

21 February 2021 8,659 1 View

Is an encrypted dataset with Microsoft SEAL compatible with Cloudsim simulator??

Hello, I would like to do homomorphic encryption using Microsoft SEAL on my dataset and then use it as an input to the Cloudsim simulator to do clustering on. Is it possible and compatible with...

16 February 2021 3,915 1 View

How to perform Kaplan-meier survival analysis in SPSS?

Hi everyone, This is my first time of attempting to run survival analysis. I have a data on patients with End-stage Kidney Diseases (ESKD). I would want to run survival probability by treatment...

16 February 2021 2,647 3 View