How to write Neural Network and ANFIS MATLAB code for multiple outputs.

Swayam Das Mohanty @Swayam_Mohanty3

07 July 2017 1 757 Report

how to write Neural Network and ANFIS MATLAB code for multiple outputs.

Mohamed-Mourad Lafifi

Dear Swayam,

Please see the same question and answer in ResearchGate 23 augst 2014 here is the link :

-How to generate multiple output for ANFIS? - ResearchGate

https://www.researchgate.net/.../How_to_generate_multiple_output...

Also i suggest you to look at links and attached files in topics.

- Neural network with multiple inputs and single output - how to change ...

https://www.mathworks.com/matlabcentral/.../155280-neural-netw...

- matlab - Neural network for multiple input and multi output (MIMO ...

https://stackoverflow.com/.../neural-network-for-multiple-input-an...

Best regards

Conference Paper Modeling and simulation of MPPT-bidirectional using adaptive...

Article Modeling and simulation of centrifugal gas compressor using ...

Article Estimation of P- and S-wave impedances using Bayesian invers...

Badges
Science topic

More Swayam Das Mohanty's questions See All

How to write the matlab code for a crack in cantilever beam for natural frequency and mode shape ?

how to write the matlab code for a crack in cantilever beam for natural frequency and mode shape

10 November 2017 9,759 0 View

How to write the matlab code for a cracked cantilever beam for natural frequency and mode shape ?

10 November 2017 9,805 1 View

Anybody can provide a MANFIS (Multiple ANFIS) sample code?

11 December 2015 2,886 1 View

How can I train the antecedent parameters of ANFIS through MATLAB code?

ALL researchers

10 November 2014 3,418 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How to plot the probability paper of Gumbel distribution using R programing?

In R-studio, there are many commands of Gumbel package. Arguments are also different. I`m asking about the alpha parameter of the Copula which must be greater than 1. If this is the one used to...

25 February 2021 5,229 3 View