How to use formaldehyde KMnO4 fumigation for Forma, Steri-Cycle Co2 incubator?

25 May 2021 1 10K Report

We have been facing a contamination problem of our cell lines and we can not use the sterilisation cycle of the incubator, so we decided to try formaldehyde KMnO4 fumigation for our incubator as it is the only source of contamination we found after investigation, I know the concentrations I should use for the fumigation, and I need to leave the heat on during the procedure.. But what about CO2? Should I turn it off? Sorry if this is a basic question, I am totally new to this.

C.A. (Kees) Kan

When fumigating our poultry houses with formaldehyde, we left the room closed totally for 24 h after starting the fumigation. Then the ventilation was switched on to get rid of the formaldehyde. Hope this information is of help to you.

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View