28 December 2023 2 2K Report

Suppose, we need to solve 1D heat conduction equation numerically to simulate the heat transfer for a steel rod where convection occurs at its surface. Now, how to solve the 1D heat conduction equation considering the convection scenario also as boundary conditions? any suggestion or resources?

More Md.Jaynal Abedin's questions See All
How can identify element number(or index) in ABAQUS scripting instead of using mask?

Dear all I want to specify random material to elements. for doing this first of all I want to create sets to elements then specify the materials tho them. to create sets in script we should...

05 September 2020 6,679 6 View

Idea for a hands-on demonstration of LabVIEW ?

Dear Members, I have started training the faculty of a govt. university of my country about LabVIEW on a part-time basis. So far they have been trained on MATLAB , Arduino , Raspberry Pi and basic...

13 March 2020 521 4 View

How many interviews are needed for a pilot study in a qualitative research approach?

I`m a PhD candidate and as part of my project, I`m going to conduct a qualitative research by doing semi-structured interviews with social entrepreneurs as the data gathering instrument. I`m...

28 July 2019 8,976 10 View

How to know abaqus and fortran are linked?

Hi. I have a technical question. I linked abaqus and fortran by a tutorial step by step and my supervisor told me to check it (successful linked) from abaqus command and I just don't know how to...

02 May 2019 438 2 View

Is there any established method to determine VItamin A from extruded fortified rice??

I am trying to analyse fortified extruded rice by HPLC. My column is C18. Is there any established method to do that?

05 January 2015 9,526 5 View

What is the advantage of bilayer graphene over single layer graphene?

What is the advantage of bilayer graphene Biosensor over single layer ones? Does it perform better than Single layer graphene sensor? if so, what makes the difference between them?

08 October 2014 1,599 5 View

How to defined sets for nodes that we know their coordinates in Abaqus scripting?

dear all. I faced a problem in defining sets for specific nodes that I know their coordinates but I don't know their node numbers how to define sets for nodes by coordinates?

01 January 1970 5,264 3 View

Similar questions and discussions
fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close