20 May 2017 3 4K Report

I have modeled grid connected inverter by using grid voltage oriented control ,everything is fine but the current is too high,where can be the fault in circuit.

Can anyone guide me

More Zakiud Din's questions See All
How to calculate Capacity retention for Lithium metal battery?

I have prepared half cell. Lithium is considered as anode in the system. Whereas, I would like to know what is actually capacity retention? How it can be calculated mathematically? On what factors...

02 June 2024 4,135 0 View

What is the reason that a Li-ion coin cell is not showing efficiency on neware battery testing system?

I have been working on electrospun membrane for Lithium Ion coin cells. I have tried to control different parameters, such as, thickness, electrolyte amount and many other parameters. I am facing...

26 March 2024 2,786 0 View

What are the possible causes of Smearing in DNA gel?

Everything is standardized as per protocol, but still this smearing is there, need suggestions from PCR experts. DNA extraction by the magnetic beads-based method. tried colony Pcr. PCR...

01 January 2024 6,888 4 View

I have been trying to dissolve isotactic polypropylene in cyclohexane for electrospinning purpose?I observed a small fraction is soluble only?

As i asked in the question statement, I observed a little amount of PP is soluble in cyclohexane. If i want to prepare a 4 %w/w solution of PP in cyclohexane, it is obvious all of it will not be...

03 November 2023 5,905 4 View

Why dissolved polymer become gel like structure?

I dissolved a medium molecular weight polymer at 135 degree celcius and after removing it from flask, i poured it into glass bottle for further use but it became a gel like structure. Can anyone...

03 September 2023 8,436 3 View

Any computational physics researcher here using ?

SCAPS-1D software for perovskite solar cell simulation.

01 September 2023 4,219 0 View

Which material paramotors value of can I use?

for perovskite absorbers like (bandgap (eV),electron affinity (eV),dielectric permittivity (relative),CB effective density of states (1/cm^3),electron thermal velocity (cm/s),electron mobility...

27 August 2023 2,194 2 View

Which material paramotors value of can I use?

for perovskite absorbers like (bandgap (eV),electron affinity (eV),dielectric permittivity (relative),CB effective density of states (1/cm^3),electron thermal velocity (cm/s),electron mobility...

27 August 2023 3,500 2 View

PLA based elastomer?

Is high molecular weight PLA a good choice for application in elastomers? The molecular weight (Mw) of PLA I am planning to use is 80000. Kindly suggest if other biopolymers are suitable instead...

28 May 2023 5,401 1 View

How to calculate number average molecular(Mn) weight of poly lactic acid?

I have to use poly lactic acid for one of my experiments. The weight average molecular weight of poly lactic acid is 80,000. How i can convert Mw to Mn in order to calculate given amount of mass...

23 April 2023 2,418 2 View

Similar questions and discussions
Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Smart grid ideas?

How to use and this is economical?

06 August 2024 3,160 2 View

How can major oxides determined by ICP-MS/ES be normalized to 100% volatile free? How does this connect with LOI?

I am analyzing cherts from different sources found within one specific geologic formation using ICP-MS/ES. My committee was asking this question about my analysis. I was not sure how to answer this

05 August 2024 7,902 3 View

How do environmental toxins interact with genetic predispositions to increase cancer risk?

I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from experts in the field. If you are an expert or researcher working on...

02 August 2024 2,627 1 View

What are some signs that an ECM is overfitting the Nyquist plot?

What can you look for to know that the circuit model being used is overfitting the data. How do you know when overfitting is occurring?

31 July 2024 7,425 0 View

Element deletion problem in ABAQUS/Explicit solver using Cohesive elements?

I had a problem for so long. I could easily delete elements in ABAQUS implicit solver but I needed to use VUMAT so I had to have Explicit solution but the element did not disappear for so long. I...

23 July 2024 10,032 0 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

I am working on III-V based tandem solar cells.Can anyone explain that solar cells work under forward or reverse biased conditions?

I want to know that n-doped side of solar cell is connected with positive or negative electrode.

20 July 2024 1,348 2 View

I need to connect expert in Urban design for Health ?

I studying PhD course in Urban design for Health. I need to know in some fileds: residental block, green open space and Transport TOD. I need connect with expert in that fileds.

14 July 2024 1,892 3 View

Why my mesh independent fastener as beam cartesian type not working in abaqus?

i have attached my model and i have used point based mesh independent fastener using attachment points and type of connector is basic cartesian but this is not working as i apply displacement on...

02 July 2024 6,293 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close