How to model the additively manufactured Ti6Al4V and analyze the fatigue bahviour of the same (in modeling itself)?

More Amit Kumar Singh Chauhan's questions See All

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How to do Pre Merger Financial Perfomance Analysis?

For Example, Company A & B merged with Company C , so during the pre merger period there are 3 company so how to do its pre merger analysis with post merger company? (either its 1 to 1 or 3 to 1)

31 July 2024 2,503 3 View

How to estimate a protien's size using Chimera or PyMol? how correct this estimated can be?

I need to know the approximate size of my target protein for Negative-stain EM. I have an alpha-fold predicted structure of the protein. I do not see any turtorial on internet for estimating the...

21 July 2024 5,732 3 View

How to bring baseline to zero for an absorbance data for chromatogram?

I forgot to autozero during the run (Size exclusion chromatography.) and later i realised i forgot to do that and the baseline was not zero but below zero (and in some cases it above zero). I...

15 July 2024 5,551 6 View

How to identify a monomeric protein species of the target without running the molecular weight standard on SEC?

I was using Superose6 10/300 Gl column for purification of my target protein. the sample consists of various oligomeric state and i would like to identify the approximate elution volume where my...

15 July 2024 5,157 2 View

How can I verify if an academic journal is a legitimate publication or a cloned version?

This question seeks to address the growing concern of cloned academic journals, which are fraudulent duplicates of legitimate publications. It aims to guide researchers, scholars, and academics on...

10 July 2024 5,966 2 View

How to properly dilute RNA for cDNA?

Hi all, I have a question regarding proper dilutions and conversions of my RNA. According to my protocol, my cDNA kit is optimized for 1ug of RNA and calls for this amount. I would like to...

07 July 2024 9,206 4 View

Can I use BSA for a Histological Blocking Solution?

Hi all, I would like to know if it is possible to use Bovine Serum Albumin (BSA) in my blocking solution for immunofluorescence muscle fiber typing. The primary antibodies' host is mouse. The...

07 July 2024 7,967 3 View

Potential Vs current density(mA/cm-2) in EC-Lab?

In Zn-Air Battery, how to plot Potential vs current density(mA/cm-2) in EC-Lab softare/BioLogic instrument. Please suggest. plot of the ref....

04 July 2024 3,807 2 View

I am conducting an experiment for oxidative stress assay for C.elegans for a phytochemical and for FUDR needed to added at L1 or L4 stage?

and will i add phytochemical along with FUDR?

28 June 2024 6,254 0 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

Some new emerging problems on application of RL for scheduling in IoT networks?

I have seen plenty of existing works on applied Reinforcement Learning (RL) policies for optimized scheduling in IoT networks including Q-learning, DQNs, and the newer ones including PPO for...

01 August 2024 8,754 2 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Hi there, someone has the SeinFit software for windows because I cannot download it?

DOS version.

29 July 2024 6,064 1 View

There is possible way to calculate experimental DOS from the UPS spectrum of the material. How to calculate the DOS from UPS?

Here, I have attached the UPS graph. I'm trying to calculate the DOS/DOVS from the UPS.

29 July 2024 4,971 1 View

Jorge Carmen Flores Juan

Hi Amit Kr. Singh Chauhan :

I don´t understand about the kind of piece you want to analize. But, I have made designs in SolidWorks 2015 software. On this platform, you can design anything, after selected a material for your piece. I attached a picture of the type of material you want to study.

Finally, you can study the fatigue behavior of the same.

I hope this information helps you.

Regards

Amit Kumar Singh Chauhan

Dear Juan,

Let me elaborate my problem precisely.While performing

While performing the experiment, one uses the Ti-6Al-4V material and deposit it by using additive manufacturing (specially DMLS) and thus print the material. The same above condition I want to model in Softwares like (ANSYS/COMSOL/SOLIDWORKS or any) and then afterward, I want to go for fatigue simulation.

Thank You,