Can we implement Cooperative MAC in underwater sensor?

09 October 2016 7,313 0 View

How to implement Learning Automata in NS-2?

How to implement Learning Automota in NS-2 simulator or C++ code.

09 October 2015 2,875 0 View

What is the best simulator for MAC protocol design in underwater sensor networks?

Best simulator for MAC protocol design in underwater sensor networks.

07 August 2014 5,929 4 View

I have a problem with S-MAC in NS-2. In Tcl code I set the Syncflag as 1 and I changed the duty cycle values.

But the results show 0 in throughput. Does anyone know what the problem is?

11 December 2012 5,065 0 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View