What is the chemical composition of chlorellin?

The chlorellin is the chemical compound which is first extracted from Chlorella vulgaris by Pratt in 1944. Spoehr in 1949 wrote that it is a mixture between fatty-acids and hyrdocarbons and its...

25 January 2021 8,538 1 View

Asalam o alikum, Can anyone please help me in interpretation of XRD data?

Actually, I want to present the in table form (dcal , dexp, 2 thita, hkl) but don't know how to find these values from data.

28 December 2020 6,769 4 View

Is it need to test Cronbach's Alpha for extracted features from data?

As Cronbach's Alpha is usually used for test the reliability of measurements given by questionnaires, however, I wonder that whether I use this test for features extracted from behavioral data. I...

26 December 2020 9,602 2 View

Doping of r-GO?

if the percentage of doping Au into rGO is too small 1~10%, is it not enough to prevent restacking of r-GO in xrd results, rGO peak appeared at 22.2 and also the peaks of gold nanoparticles so...

21 December 2020 6,091 3 View

XRD peaks for gold nanoparticles ?

is the concentration of gold salt that were added will affect on the peaks appeared. i added a very little amount of gold salt to dope graphene oxide and not all the peaks that proved the...

17 December 2020 9,275 3 View

How can AI and ML be applied for real-time dynamic predictive analytics of cyber risks?

Anyone has any ideas on how you could use AI/ML for real-time dynamic predictive analytics of cyber risks? There is a discussion on AI and cybersecurity, I have seen that, but if you wanted to...

15 December 2020 1,264 3 View

If someone has the pdf file of below mentioned reseach paper?

14 December 2020 5,935 3 View

I saw sparkles in my samples?

i am trying to dope boron in graphene oxide , and after i take out my samples from the oven i put them in the microwave for 40 sec , and i saw sparkles . and fume also i couldn't understand why

16 November 2020 6,852 5 View

QUERY REGARDING acdS gene (ACC deaminase encoding gene) Amplification?

08 November 2020 3,249 2 View

Does anyone observe formation of deposits on Silver thin films in clean room atmosphere ?

I pattened Silver by E beam lithography followed by e beam deposition and lift off. Over a period of two days, they seem to be developing deposits on the surface. My substrate does come in contact...

27 October 2020 5,355 3 View

What is the best way to keep an anaerobic chamber anoxic in the absence of hydrogen?

I'm a graduate student who works with an anaerobe, so I often work in an anaerobic chamber. I've been working on an assay that involves the steady-state of the quinone/ quinol pool. Anoxic...

03 March 2021 2,971 1 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View