How To Find/Calculate the Number of Fluorescent Lamps in a Sub Circuit?

More Ahmad Kalaie's questions See All

A Voltmeter, an ammeter (Ampere meter) and a battery cell are connected in series. It is observed that ammeter practically shows No Deflection. Why?

31 December 2016 7,139 0 View

Why Parallel Connection is Mostly Preferred over Series Connection?

11 December 2016 6,569 0 View

Which oil can be used in transformer?

11 December 2016 1,067 0 View

How to Calculate/Find the Rating of Transformer in kVA (Single Phase and Three Phase)?

11 December 2016 8,475 0 View

How to find The value of Burnt Resistor ?( By three handy Methods )?

11 December 2016 7,174 0 View

What are the existing predictive reference generators for active filters in power systems???

11 December 2016 7,850 0 View

What is the difference between AC and DC Resistance & How to calculate it?

11 December 2016 904 0 View

What are the drawbacks of walsh codes?

11 December 2016 4,025 0 View

A step up transformer which has 110/220 turns. Can we replace it with 10/20 turns?

.Turns ratio is same shall its rating be same? Give appropriate reason?

11 December 2016 10,068 0 View

How to calculate or Find the value of SMD Resistors?

11 December 2016 2,996 0 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

Are there any commercially available Donkey anti-Alpaca secondary antibodies?

Are there any fluorescently labeled anti-Alpaca secondary antibodies raised in Donkey? So far I have only been able to find anti-Alpaca secondaries raised in Goat. Or is this not possible due to...

04 August 2024 4,255 1 View

Why results of ROS flurescence are negative as there was no bacteria within?

Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...

04 August 2024 5,974 3 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

How to calculate the molar proportions of the oxides from the XRF analyses?

02 August 2024 2,565 2 View

What are some signs that an ECM is overfitting the Nyquist plot?

What can you look for to know that the circuit model being used is overfitting the data. How do you know when overfitting is occurring?

31 July 2024 7,425 0 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

Bhupendra Desai

Number of lamps= Total current/ Current per fluorescent lamp, (if are identical).......

Chaouki Hannachi

hello Ahmad,

check also this link,

http://www.electricaltechnology.org/2012/12/how-to-findcalculate-number-of.html

B.regard

Prakash Chandra Tah

The lamps are in series or parallel in your circuit. And if they are in series then total supply voltage and voltage rating of each lamp to be taken into account and for parallel current capacity of source and current rating of each lamp to be taken into account.

Wayne Brod Beskow

Take into account the power of the lamps and the luminescence. Calculate the equivalent load according to the information provided by the manufacturer.