How to convert metallic fine powder to flakes?

More Dr. Pallavi Deshmukh's questions See All

Are you looking for research collaboration ?

we have few papers ready for submission, and we need one co-author for each article who can pay article fee. Interested authors may text here or contact me on my following email id [email protected]

29 July 2024 6,626 0 View

Dear researchers. pl help how to plot jablonski energy level graph and magnetic hysteresis curve in origin?

through origin software

17 July 2024 4,991 0 View

How is artificial intelligence being utilized to enhance the diagnosis and treatment of sleep apnea?

AI has the potential to improve the management of sleep apnea by personalizing treatment, enhancing diagnostic accuracy, and advancing our understanding of the condition.

03 July 2024 9,393 2 View

Action research design is Quantitative Studies or Qualitative Studies?

14 June 2024 1,684 1 View

Offer or collaboration for book publications?

Dear Profs/ Scientist, if any one is interested or have plan to publish a good quality books/ book edited , I can contribute/help such type of research works . My research...

06 June 2024 5,932 2 View

How to draw SeDeM diagram for preformulation study of drug and excipients?

What is SeDeM expert tool? Is it in silico tool and how to draw the SeDeM diagram for preformulation study? Kindly suggest.

06 June 2024 4,408 0 View

Call of book chapter ?

CALL FOR BOOK CHAPTERS (No Publication Fee) Scrivener Publishing/wiley Dear Prof,Scientist/ experts, Greetings. We are editing the book entitled " FET Devices: Post CMOS Theory and Applications...

28 May 2024 9,284 0 View

Is there a Raising awareness of indigenous medicine among metropolitans?

The growing interest in holistic health practices is leading to increased awareness of indigenous medicine among metropolitan populations. While challenges exist in terms of access and cultural...

09 May 2024 7,041 1 View

Why many times RG is sending email? Is this person is co author or published article? Many times it is been sending.?

Pls dont send many times email is this person is co author or published article? Many times it is been sending. Pls stop it ok

06 May 2024 3,964 3 View

What is the protocol to maintain 260/280 and 260/230 and to get pure DNA from ruminant faeces using Dneasy PowerSoil pro Kit?

I used the Dneasy PowerSoil Pro Kit. But I didn't get a good ratio of 260/280 and 260/230 and didn't get a good band after electrophoresis. I maintain all procedures according to the...

29 April 2024 1,242 4 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,493 3 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

How to Dedust Activated Carbon Granules?

Dear all, We are producing activated carbon from hazelnut shells but have an issue about the dust of the a.c. granules also known as the dust film on granules. Linear vibrating seives doesn't do...

11 July 2024 9,782 2 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

Nadir Fadhil Habubi

you can make use from

https://patents.google.com/patent/US3099080A/en

Dr. Pallavi Deshmukh

Nadir Fadhil Habubi thank you , I will through the patent

Regards

Amit Abhash

I think you should go for ball milling to convert fine powder to flake; Various methods can be employed to produce the alloys you mentioned either using powder metallurgy or liquid metallurgy route