How to Compile & Run OpenMP C Program on Gem5 Simulator ?

09 September 2017 0 6K Report

Good Evening to All. I'm an Undergraduate Student and Currently i am Researching About Multi-threading Programming on Multicore Processor. I Want to Compile & Run a Multi-threading C Program (With OpenMP). How Can i Compile & Run a OpenMP C Program on Gem5 Simulator. Please Help Me.

Thank You.

Regards,

Litu

Badges
Science topic

More Litu R Hossain's questions See All

How to Execute Multi-threaded program (As like OpenMP, Pthread e.t.c) on gem5 SE Mode ?

Hello Everyone. I'm an Undergraduate Student and Currently i'm Researching About Multi-threading Programming on Multicore Processor. I Want to Compile & Run a Multi-threaded C/CPP Program...

31 December 2017 1,844 0 View

Help Help Please. How to Work Multi-threading program (As like OpenMP, Pthread e.t.c) on gem5 Simulator ?

Hello Everyone. I'm an Undergraduate Student and Currently i'm Researching About Multi-threading Programming on Multicore Processor. I Want to Compile & Run a Multi-threading C/CPP Program (As...

08 September 2017 6,013 0 View

How can i compile & run a c program (with OpenMP) in gem5 Full System?

I am an undergraduate student working on my thesis about parallel programming. I am using OpenMP model. Now i want to use gem5 for measure performance. That's why i install gem5 Full System...

02 March 2017 1,324 0 View

How to access MSCI KLD Stats and Sustainalytics?

Hello all, I'm currently working on my undergraduate thesis and I'm having difficulties trying to access KLD Stats and Sustainalytics because my campus Airlangga University and apparently other...

02 March 2021 8,525 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

How do I add a udf to Ansys fluent and does it need to be compiled before hand ?

I have a Define_CG_Motion udf written in c where do I add it to my Ansys fluent project and does it need to be compiled before that?

21 February 2021 9,347 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View