09 September 2016 1 3K Report

 The band edge position(Conduction band minimum) of CaTiO3 in AgBr/CaTiO3 powder can be calculated using the equaiton Evb=X-Ee+0.5Eg. Which Eg value should be used in the equation i.e Eg value calculated for pristine CaTiO3 or AgBr/CaTiO3 should be used

More Zameer Hussain Shah's questions See All
AgBr/SrTiO3 was photoreduced to obtain Ag/AgBr/SrTiO3. Ag is detected in the XPS spectrum but not by XRD. What can be the explanation?

AgBr/SrTiO3 was photoreduced in a methyl orange solution under visible light for 50 seconds. The powder color turned from whitish to dark brown indicating the successful reduction of AgBr to...

31 December 2016 8,839 6 View

I have synthesized Ag/AgX(Cl, Br)/CdTiO3 via microemulsion. The xrd peaks intensity is much lower in the case of Ag/AgBr/CdTiO3. Any Explanation?

The XRD patterns are presented in the Fig.

07 August 2016 1,935 8 View

The UV-vis absorption spectra of Ag/TiO2 and CuO/TiO2 show broad absorption between 400-800nm. Can anyone explain these absorption bands?

the figure is attached.

02 March 2016 2,992 4 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close