How to add "Result watch" in parameter sweep

01 January 1970 0 4K Report

I am getting Fig.1. But I want to get Fig. 2 . The procedure to get Fig.2 is a result watch in CST.

If anyone knows please post the procedure. It will be beneficial for my study. Thanks

Badges
Science topic

More Kiran Kumari's questions See All

Why the battery connected on the load side for storing purpose is taking the volatge /current at whatever rating it is given in matlab simulation?

I am designing a DAB DC DC Converter and when I am connecting a battery block in Matlab and fix its specification lets say 350 V and 25 A, when I am giving input as 600V, Battery would charge to...

11 February 2021 3,110 1 View

How do I connect DAB DC DC Converter to a battery in matlab simulation ?

I am trying to model a DAB converter and I need to observe the power transfeered to the load side on varying the phase shift between two bridges, hence I couldnt take a constant load e.g...

09 February 2021 6,489 3 View

Statistical methods for comparing gene expression curves?

Hi all, I have generated two gene expression curves by measuring bioluminescence every 10 mins for 12 hrs. These curves tend to overlap at at some time points, while a difference can be seen at...

02 February 2021 2,613 7 View

After G actin polymerization and labelling I didn't got filaments. Why?

Purified G actin and got 42kda band and an additional band just below it. While performing G actin polymerization and labeling with rhodamine-phalloidin I didn't observe filaments under the...

20 January 2021 3,751 2 View

In which solvent dissolve silver nanoparticles for XRD pattern study through NMR ?

The silver nanoparticles, which are solid form and I want to study the XRD pattern of this nanoparticles by Nuclear Magnetic Resonance (NMR), so I asked which solvent are used for dissolve of...

13 January 2021 3,434 4 View

Why there is need to calculate the chlorophyll content and chlorophyll index. What protocol should I used for calculating chlorphyll in mustard?

I want to know the best and effective method/ protocol to calculate the chlorophyll from mustard plants. Please suggest some relevant and the methods or protocols from which I can easily calculate...

05 January 2021 9,882 3 View

Buckling of Smart composite plates using FEM ( MATLAB code)?

Can anyone help me with the FEM coding for Buckling of composite plates using the FSDT or HSDT - Source or the helping material (textbook, research paper etc) - Geometric stiffness matrix...

03 January 2021 3,059 3 View

Only one clear RNA band on gel?

The RNA quantity in nanodrop is about 1 microgm. 260/280 ratio is also around 2, still I am not getting clear bands on gel. What can be the reason?

30 December 2020 1,731 2 View

Asalam o alikum, Can anyone please help me in interpretation of XRD data?

Actually, I want to present the in table form (dcal , dexp, 2 thita, hkl) but don't know how to find these values from data.

28 December 2020 6,769 4 View

Is it need to test Cronbach's Alpha for extracted features from data?

As Cronbach's Alpha is usually used for test the reliability of measurements given by questionnaires, however, I wonder that whether I use this test for features extracted from behavioral data. I...

26 December 2020 9,602 2 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

Compact antenna for the frequency range 1 MHz-5 MHz?

Hello everybody! I have a problem with developing a compact antenna for the 1MHz-5MHz frequency range. Tell me what type of antenna can be used and what books and articles to read to perform this...

27 February 2021 7,710 4 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

Is there a way to use waveguide ports for circular antenna design in CST?

Hi, whenever i use circular array i get this error "Waveguide ports must be aligned with Cartesian coordinate planes for the transient solver" Does anyone use circular array with waveguide ports?...

09 February 2021 3,609 8 View

How to model in HFSS or FEKO Free Space Material Characterization?

I am having trouble setting up this problem in HFSS or FEKO. In HFSS, I've tried both FEM and FEBI-IE solvers. With FEKO, I've tried it's MoM solver and default settings. I am would like model...

09 February 2021 375 2 View

What is best solution for optical metamaterial design calculation: HFSS, COMSOL, CST?

Dear all, Now I'm selecting FEM for design of metamaterials on NIR~VIS frequencies, and keeping 3 software: ANSYS HFSS, COMSOL with wave optics module, and CST STUDIO SUITE. Could you give me...

09 February 2021 9,517 2 View

Which journals (Q1,Q2) accept simulation based design and results of antenna if fabrication and testing facility is not available?

I need a list of good (preferably Q1,Q2) journals that will accept research papers prepared on designs done with the help of simulation software e.g CST, HFSS etc.

08 February 2021 9,636 5 View

How to achieve the sensitivity diagram of a sensor in CST?

I wanna design a sensor in CST 2021 for the first time and I don't know how to achieve the sensitivity diagram of the sensor in CST. Could you plz help me to do that? I appreciate your response...

26 January 2021 6,864 1 View

What is corrct way to define ports when simulating FSS and surface waves in CST?

I need to simulate a mushroom FSS and I'm struggling with the ports. What's the correct way to define them? Should I construct a proper SMA connectors, or is it enough to put a waveguide ports...

19 January 2021 6,590 4 View