What is the reason of collapse of water tank shown in the attached you tube?

https://www.youtube.com/watch?v=WLEkC_JbTsQ

03 April 2017 1,021 2 View

No title

02 March 2017 8,545 19 View

Why do BS8007 specify the allowable crack width of water retaining structure as 0.2mm for severe or very severe exposure?

Why 0.2 mm crack width?

02 March 2017 9,166 3 View

Which type of multiple-cell box girder is better, cells connected by top flanges or cells connected both by top and bottom flanges?

How we can design box girder bridge?

02 March 2017 9,977 3 View

What is the effect of rusting on steel reinforcement?

How does rust affect on the bonding between steel bars and concret?

02 March 2017 3,267 10 View

What is the difference between working stress approach and limit state approach?

02 March 2017 415 2 View

It is not necessary to design nominal reinforcement to piles. Is it true?

Can we use same code provisions of columns for piles?

02 March 2017 7,705 3 View

In carrying out compression test for concrete, should test cubes or test cylinders be adopted?

Relation between cubes and cylinder

02 March 2017 5,645 4 View

If concrete compression test fails, should Schmidt hammer test be adopted as an alternative test to prove the concrete strength?

Non destructive tests

02 March 2017 5,232 31 View

What is the meaning of P-delta analysis?

Some codes provisions refer to this type of analysis.

02 March 2017 8,549 5 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Which is the most convenient manufacturing software for Additive Manufacturing?

Which tools can be used to generate machine codes for additive manufacturing?

02 March 2021 7,220 2 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

No title

Does anyone have the experience of using Taq Man probes in the QIAGEN Rotar- Gene qPCR machine?

01 March 2021 5,311 1 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View