In layered materials due to presence of stacking fault in stacking sequence intensity of some of XRD peaks gets altered. If we heat material or if we cool it, how does this will affect intensity of those XRD peaks.
See following papers:
https://www.sciencedirect.com/science/article/pii/0025541678901945
http://www.jmst.org/article/2016/1005-0302/1005-0302-32-8-790.shtml
Follow
Syed Asad Ali Zaidi, Thanks for your response. I will read these articles.
I am looking for a free software for text mining and sentiment analysis for my research on customer review mining (it involves calculating polarity of attributes,opinion oriented information...
25 February 2021 1,920 6 View
Why dielectric anomaly peak related to the defect dipoles present in the paraelectric region (around 450 K) of temperature dependent dielectric constant curve tends to disappear? The dielectric...
25 November 2020 209 2 View
Generally it is known that SEM is based on the principle of interaction of electron beam with matter. Proton and ion beam can be used instead of electron beam? How their interaction will be...
27 September 2020 4,432 9 View
India's New Education Policy ( NEP- 2020) has scrapped the M.Phil. Degree. Do you think the fresh Master's students can go for Ph.D. directly? Many scholars have gradually entered into Ph.D. by...
31 July 2020 7,863 13 View
28 April 2020 8,048 3 View
Hi, I am not clear as to how to decide the frequency range required for the approximation of a FOPID controller used to control a power electronic converter. Can anyone suggest some papers which...
27 March 2020 1,454 2 View
21 March 2020 2,530 3 View
SEM micrograph of doped Barium Titanate ceramics had certain white spots on the grains? What can be the possible reason for such white spots?
18 March 2020 3,275 4 View
How to find quantum yield of a fluorescent material?
17 March 2020 7,471 2 View
I did analysis of box girder bridge in SAP2000, it is giving bending moment in entire bridge section. I want to know where it is giving moments for entire bridge section.
10 September 2019 2,991 3 View
The figure shows DSC cooling (blue) and 2nd heating (green) curves (step: 10 K/min) for a commercial sample supplied as Atactic Polypropylene (APP). The heating curve illustrates two major...
03 March 2021 5,857 3 View
Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...
01 March 2021 7,168 9 View
Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...
01 March 2021 3,867 3 View
Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?
01 March 2021 9,785 3 View
I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...
01 March 2021 9,015 2 View
Hi, I am running a size exclusion chromatography experiment with a buffer containing Potassium Acetate as a salt. I analyse these fractions through SDS-PAGE. After boiling my SEC fractions in...
01 March 2021 2,622 3 View
I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...
01 March 2021 6,450 5 View
I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...
28 February 2021 8,626 3 View
I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...
27 February 2021 8,128 1 View
Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...
26 February 2021 6,253 3 View