How do I create a custom library in Simulink and use it in the another simulink model ?

More Kangujam Anelis's questions See All

How to set the window size in neural network using nntool?

How to set the window size in neural network using nntool?For example:In modelling a wind energy system in microgrid, we have implemented feedforward neural network and we have set the window size...

10 November 2018 880 4 View

How can two neural networks be compared for regression based on training and testing results ?

07 August 2018 7,658 5 View

What is the allowable value of mse in load forecasting in neural network?

In STLF using nntool, mse of 40 is obtained. Is there any allowable range for the mse value in load forecasting? If so,what is the allowable value of mse in load forecasting?

07 August 2018 9,693 4 View

I am getting different result whenever I run my neural network using nftool?

Actually ,I built my neural network using nftool only. I didn't use any code .Whenever i run my neural network I get different results of mse, R, performance plot, error histogram, training plot...

07 August 2018 4,320 6 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

22 February 2021 3,697 1 View

How can I get "Matlab/Simulink model for Droop/Reverse Droop controllers"?

Dear Professors, Colleagues and Friends I need to develop a simple Matlab/Simulink model of reverse droop controller for a simple LV MG. How can I get a simple one to use it as a sample? A basic...

22 February 2021 8,647 2 View

I can detect my protein but the encoding DNA sequence has stop codons within. Should I ignore the stop codons?

I constructed a synthetic DNA library (scFv, VH-VL orientation) with a 3' reporter and 8x histag. I cloned and expressed this gene following which I performed an ELISA. The ELISA results suggested...

19 February 2021 7,006 5 View

Why are the modelled and circuit system different in response for controlled buck converter?

[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...

16 February 2021 5,060 10 View

How do I check the quality of my viral RNA prior to metagenomic sequencing?

I am doing metagenomic sequencing without enrichment for an RNA virus. After my RNA is extracted from the blood I am doing library prep with the NEBNext Ultra directional RNA library prep kit for...

16 February 2021 5,101 2 View

How to remove the species data from rda data frame in R (only remain the sites/samples point)?

Dear everyone, When I using the rda function in r, I met this question. As you can see in the figure, there are a lot of deep blue points which refers to the species. But I would like remain...

15 February 2021 8,982 2 View

What's support me on Simulink Matlab Model of Regenerative Braking in DC Traction ?

I have a thesis on Utilize the electrical power from Regenerative Braking in 750 Vdc Traction by simulation in the Program MATLAB Simulink. I made the Power Load flow from 24kV to Traction...

08 February 2021 2,532 1 View

How to find statistical data of EEG signals?

Hi all, I hope everyone is doing good. I am working on Machine Learning, I am working on EEG data for which I have to extract statistical features of the data. Using mne library I have extracted...

29 January 2021 6,686 1 View