How can i send S5 timer value to the PLC from MATALB through the OPC Scout ?

03 March 2017 0 5K Report

Hi to all,

I am working on PLC S7-300 and i am trying to make a connection between PLC S7 300 to MATLAB SIMULINK via OPC.

I am going to send S5 timer value (such as s5t#50s) to the PLC programming environment from SIMULINK(MATALB) through the OPC Scout.To do this it should be defined as memory word (mw) and BCD format. But when i set this value from SIMULINK, it is set wrong value in PLC.

would it be possible to guide me please ?

Thanks.

Badges
Science topic

More Davood Shaghaghi's questions See All

How can I calculate the airway resistance of a tube?

03 April 2015 4,190 3 View

How can I design a back stepping controller?

Hi everybody, How can I design a back stepping controller for this system? h1 and h2 are states of the system and q is the input. Because, in Khalil's book, design is said for specific type of...

11 December 2014 1,381 8 View

How can I identify a hysteresis system ?

Hi everyone, I want to identify linear model for a pneumatic proportional valve that has hysteresis behavior. I split region of system to 9 sub-regions and apply a PRBS as input of system for...

11 December 2014 5,552 9 View

Is linear analysis in controller design tool (in MATLAB simulink) applicable to unstable systems?

Hi every body, I have a nonlinear system model in simulink. This system is unstable and I want to design a controller to stabilize it. Due to this, I want to linearize this model and then design a...

11 December 2014 3,965 6 View

Does anyone know about modelling of pneumatic elements ?

11 December 2014 10,002 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

How to plot the probability paper of Gumbel distribution using R programing?

In R-studio, there are many commands of Gumbel package. Arguments are also different. I`m asking about the alpha parameter of the Copula which must be greater than 1. If this is the one used to...

25 February 2021 5,229 3 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View