Does anyone use antinuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples?

I am looking for anti-nuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples. Any suggestions highly appreciated. Thank you.

28 February 2021 6,512 3 View

Treating Intermediate Variable in Linear Regression Analysis in SPSS?

While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...

25 February 2021 4,591 5 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

Having trouble with qPCR amplification plots. My curve's never seem to reach a plateau. Any ideas?

The parameters of the curve all seem acceptable, typically reactions results are above 0.9852, -3.1 to -3.6 slope, and 90-110% reaction efficiency. The results seem to be what I would expect from...

04 February 2021 1,138 3 View

How can I get rid of the bubbles in the SBS membrane?

I used methylcyclohexane/ ethylcyclohexane / n-butyl acetate mixed solvent to dissolve thermoplastic SBS & terpene resin. The mixture is then poured onto a glass substrate. After solvent...

24 January 2021 8,306 3 View

Can anyone provide me a protocl of Native PAGE with the 30% terminal resolving gel concentraion?

I am separating the AuCNs, which are Au nanoclusters. I used the 3% stacking and 30% resolving polyacrylamide from the reference. Eachtime when the resolving gel is polymerizing, plenty of heat...

22 January 2021 8,522 3 View

After G actin polymerization and labelling I didn't got filaments. Why?

Purified G actin and got 42kda band and an additional band just below it. While performing G actin polymerization and labeling with rhodamine-phalloidin I didn't observe filaments under the...

20 January 2021 3,751 2 View

How to Import .inp file from abaqus CAE to Ansys perfectly?

I am trying to import an Abaqus .inp file to Ansys but it does not import the whole assembly but only imports a single part. How to solve this.

17 January 2021 5,450 3 View

Which one I should choose in Abaqus ?

Hello, plese give me your idea! I simulate one slab concrete affected by temperature at top and bottom surfaces. after that, have a static load distribution with small area put on top surface. I...

12 January 2021 5,769 4 View

No title

11 January 2021 3,284 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

What is Flat Lens Antenna?

28 February 2021 5,433 3 View

Compact antenna for the frequency range 1 MHz-5 MHz?

Hello everybody! I have a problem with developing a compact antenna for the 1MHz-5MHz frequency range. Tell me what type of antenna can be used and what books and articles to read to perform this...

27 February 2021 7,710 4 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Why does the sum of reaction forces not match the force component of a Free Body Cut in Abaqus?

I am using Abaqus to simulate a plate with in-plane loading. The boundary conditions allow the right edge to move up and down, the displacements on the left edge are fixed. There is no rotation...

23 February 2021 711 3 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View