How can I design a SPI (serial peripheral interface) to LVDS (Low voltage differential signalling) converter?

17 April 2015 1 5K Report

Hello,

I would like to build an electronic circuit for SPI to LVD converter. Please help me with concept in designing this.

You can use LVDS Driver and LVDS receiver. with a typical differential input threshold of 100mV, to LVTTL signal levels.

we shall have further discussion on this understand your scope.

Badges
Science topic

More Sravan Aitha's questions See All

How to derive the Phase Inductances(Lu, Lv and Lw) for a three phase PMSM motor from Ld and Lq values?

I would like to calculate the individual phase inductance values of 3-phase motor from the availabe Ld and Lq values. Could anyone please let me know few hints / scripts in Performing the...

08 May 2022 7,277 0 View

What are new research areas to focus on for breast cancer detection using Hyperspectral Imaging?

I started my literature exploring HSI and i found out breast cancer to be an interesting area to work on . Since i am new to this technology and lots of research has been going on worldwide i...

09 March 2022 5,543 1 View

Can anyone tell, what are the popular commercial products available in market (with codes) for nano filler used in polymer matrix/nano-composites ?

I'm looking for commercial nano filler available products (like clay, ZnO, TiO2 etc.) for applications like Automobiles, Aerospace, Fire-retardants, Sensors etc.

06 February 2020 4,056 3 View

How to integrate genetic algorithm in vm initial placement in cloudsim plus?

Dear fellow researchers, I have implemented a Genetic algorithm for initial vm placement and I am calling it in an extended class of vm allocation policy, precisely in defaultfindhostforvm...

29 October 2019 5,735 0 View

Can we identify the genes binding to a protein if we know the nucleic acid binding cites of that protein?

I have a protein sequence and I have identified the nucleic acid binding sites using DRNApred tool. Can I identify the possible genes interacting with the protein using the nucleic acid binding...

19 August 2019 1,456 2 View

Can I configure firewall in NetSim?

How do I setup the firewall configuration at a node? Are there options for access control list? If yes, is code modification required for this?

09 July 2019 5,264 4 View

Energy consumption in Netsim IOT module?

How do I get energy consumption over simulation time for each sensor in NetSim v11.1. The results window only gives the summary results, but I need to find the energy consumption over the...

16 April 2019 7,910 11 View

Need to understand the data rate for different MCS for 802.11?

I am running 802.11 simulations in NetSim and want to understand how the data rate is determined for different MCS in 802.11. Thank you.

31 December 2018 2,014 4 View

How to capture packets in wireshark from NetSim?

I would like to plot the TCP congestion window of a node. Currently, I am doing it from the packet trace in NetSim. However, I would prefer to do it in wirehshark since it is the industry standard...

29 October 2018 1,272 8 View

How can I simulate different TCP congestion control algorithms?

I need to simulate and analyze different congestion control algorithms of TCP like Old Tahoe, Tahoe, Reno, New Reno, BIC and CUBIC and study the difference between these. What may be a good...

15 October 2018 8,767 13 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Is it possible to improve the reforming section of the Haber-Bosch process without using air separation units?

A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...

01 August 2024 7,051 5 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

How to troubleshoot error E1 on Biorad Powerpac Basic despite using sufficient and fresh buffer?

I have used this BIorad Powerpac Basic for 4 years now, before which it was used for another 5-6 years. Generally we addressed the E1 error by compensating with fresh buffer and/or filling the...

01 July 2024 7,104 1 View

Self discharge of freshly made NMC half cells and voltage stabilizes at 3.3-3.5 V vs Li/Li+ during charging. What can affect it?

I am making Li half cells using NMC as cathode. The OCV is around 3 V but it self discharges and during charging the voltage increases to 3.5 V and then drops to 3.3-3.4 V and stays there. I have...

23 June 2024 842 3 View

How to predict the efficiency of a very low speed Railgun Actuator/Lorentz Force Actuator?

I'm not an electrical engineer or anything related to that subject, so my apologies if I understood something incorrectly. Well, I read somewhere that the slower the railgun is, the higher its...

23 June 2024 1,082 0 View

What is the ground state configuration of 2D-isotropy Heisenberg model at low temperature under classical MC method?

The Mermin-Wagner theorem has pointed out that there should be no spontaneous magnetization at finite temperature in 2D-isotropic Heisenberg model, or there will be no long-range ferromagnetic...

16 May 2024 7,070 2 View

Why battery is not taking higher current whencharging and also a high voltage drop?

sodium ion battery is not taking higher current when charging and also has a high voltage drop

06 May 2024 3,182 1 View

How to set parameter for galvanostatic charge–discharge (GCD) and Chronopotentiometry (CP) test in a work station (potentiostat) for supercapacitor?

Respected All, Recently I have been started working in supercapacitor. I am completely new in the field of supercapacitors. I have performed the CV. The weight of the active materials I used was...

03 May 2024 5,940 0 View

How do I extract Schottky barrier, ideality factor from temp. dependent JV, using Richardson plot or Arrhenius plot using origin. What Js is used?

I possess data on JV, current, voltage, and current density obtained from a simple diode (metal-semiconductor). Currently, I aim to plot the Richardson curve and Arrhenius plot to determine the...

24 April 2024 5,395 6 View