HFSS errors........... SOLVER_OUT_OF_MEMORY: FEM domain 1 requires approximately 132 GB of RAM....???

More Anoop P's questions See All

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

How to interpret results of AST for Pseudomonas aeruginosa?

While doing AST for Pseudomonas aeruginosa, after incubation, no zone of inhibition observed in the plate near the well. wells surrounded by bacterial growth, when the same plate observed under UV...

25 July 2024 9,229 1 View

What is the Principle of Cysteine-carbazole-sulfuric acid reaction with glucose?

I have been looking for the principle of Cysteine-carbazole-sulfuric acid reaction in research papers and books, but couldn't find it. This reaction is mainly used for the quantification of...

23 July 2024 3,891 0 View

How can AI technology to enhance the agricultural productivity?

Farmers no longer have to apply water, fertilizers, and pesticides uniformly across entire fields. Instead, they can use the minimum quantities required and target very specific areas, or even...

22 July 2024 8,296 3 View

Can a paper that is posted as a preprint in a database with DOI, can be reviewed in another journal and accepted for publication??

It happened that I am asked to review a paper for a journal. Incidentally, the paper is posted as a preprint in another database as open access with DOI. It is completely citable. Now, should I...

17 July 2024 1,831 4 View

Do software tools exist to assess the economic and technical practicality of introducing new food products, such as yogurt with modified starch?

This question explores the world of food innovation and asks if there are computer programs that can analyze the financial and technical feasibility of introducing new food products. For instance,...

13 July 2024 7,446 0 View

How can I verify if an academic journal is a legitimate publication or a cloned version?

This question seeks to address the growing concern of cloned academic journals, which are fraudulent duplicates of legitimate publications. It aims to guide researchers, scholars, and academics on...

10 July 2024 5,966 2 View

To what extent Google Scholars Citations system is reliable?

1. I was shocked to discover yesterday that my research citations on Google Scholar had dropped to 2383 from 2419 a week ago, and they are now up to 2391. 2. My citations three months ago were...

28 June 2024 2,846 2 View

How can i calculate the band alignmet of Sc2CO2/BlueP heterostructure from DFT?

I know the work function and band gap of each monolayer and heterostructure. I calculated mulliken electronegativity(X) of Sc2CO2 and Bluep. From that i found Ev = X- 4.5+Eg Ec = Ev-Eg, where Eg...

28 June 2024 9,360 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

What do you consider to be the most relevant elements of EEG for studying cognitive biases?

I've seen articles that primarily focus on alpha and beta activity in the frontal regions, but these studies often compare healthy subjects with those having various pathologies. I haven't seen a...

31 July 2024 7,259 1 View

In SEM, if a latent variable consists of three observed variables, and each observed variable has four items, what should I do?

Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...

31 July 2024 3,913 6 View

How to improve peaks separation in HPLC?

Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...

30 July 2024 435 3 View

Anik Ghosh

Hi,

This thing happened when you choose high accuracy for your parametric simulation. You should use a computer with high RAM or decrease the simulation accuracy. Select fewer points and simpler mesh. In that case your accuracy will reduce.

Nitin Kumar

Agreed with Anik Ghosh and Pratik Ghate