Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

What are the application of Fixed points thoery in Chemistry.?

It is said that fixed point theory has lot of applications not in the field of mathematics only but also in various areas. So I am looking for applications in Chemistry only..

26 February 2021 3,533 1 View

How can we raise the figure when we writing a paper with Latex ?

Hi, everyone. I'm a starter to write a paper by Latex. But I have some difficulty using it. I'm writing the paper with 2 columns. And, there is one figure that occupies the 2 both-sides. I want to...

26 February 2021 3,738 3 View

Satellite orbit estimation using Recurrent Neural Network - what should I use?

Hello, I am a master's student studying in Yonsei Univeristy, Korea. I am trying to estimate the state of satellite, using Neural Network. Below is a simple flow of my study. 1. Train (t0 ~ t1)...

23 February 2021 6,383 3 View

What is the system of units used in the thermal conductivity by Spitzer and Harm?

23 February 2021 9,253 1 View

Level 1 pre-post multilevel regression: Panel data or ANOVA approach?

Dear colleagues, I am currently teaching myself in multilevel analysis using educational data. I found few to zero literature on basic analysis methods. In my context we frequently use level-1...

17 February 2021 9,378 5 View

How many days do we need to detect adoptively transferred Treg in the tumor site in tumor-bearing recipient mice?

Hello, I've got a plan to isolate mouse splenic Treg (WT and KO of target gene) and inject these CD45.2 Treg into tumor-bearing CD45.1 mice. My question is how many days do I need to wait to see...

11 February 2021 8,238 1 View

Is it possible to antibody labeling with FITC cause antibody disfuction?

Hello, I studied how much bound my test antibodies to the target antigen using FITC labeling to test antibodies. I tested 3 types of antibodies, the elisa binding affinity and cytotoxicity...

07 February 2021 8,335 2 View

Can you use MTS assay with cells cultured in media containing phenol red?

I am trying to run a cell viability assay with LN229, but these cells are cultured in DMEM which contain phenol red. Is the MTS assay sensitive to the additional of phenol red in the media? If so,...

03 February 2021 9,478 2 View

How to extract RNA from brown adipose tissue(BAT)?

30 January 2021 6,610 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How to do buckling analysis in ansys apdl for laminated plate with PZT 5H attached?

I am doing buckling analysis of laminated plate surface bounded with two piezoelectric PZT 5H and axial compressive load is applied. I am getting an error, No ANEL table exists for material 2....

16 February 2021 510 1 View

What is the maximum voltage a piezoelectric PZT layer can handle?

I have a circular PZT layer deposited by PLD method. The dimensions are: 20um diameter and 350nm thick. It has 100nm Pt electrodes sputtered on the top and bottom. I would like to know what is the...

25 January 2021 688 5 View

How to match results from based paper and Ansys Workbench in modeling piezoelectric?

Hi guys, I have modeled a laminated composite beam patched with piezoelectric layers in Ansys Workbench, but the results are far away the results reported in base paper. I have attached the...

13 January 2021 7,356 3 View

Matlab code of the differential quadrature method ??

I need a Matlab code of the differential quadrature method to solve the equation of motion of a vibrating piezoelectric beam knowing that I used Euler Bernoulli's model ??

03 January 2021 7,178 3 View

How to convert mV output into MPa?

I am working on acoustic characterization of microbubbles using two transducers arranged at 90 degrees. During calibration, I am receiving response in dBm or mV. How I can know the PNP of my...

14 December 2020 1,814 5 View

Modeling and Simulation of Radial Piezoelectric Transducer?

I need some one working in comsol

10 December 2020 8,442 3 View

How to decrease the difference between the simulation result obtained by comsol and analytical result ?

Hello, I am working on a piezoelectric energy harvester in comsol so I coupled the electrical circuit interface with the piezoelectric device multiphysics. I tried to confirm these results with...

07 December 2020 1,007 2 View

How to deal with a Solver Pivot Error in Ansys (piezoeletric sensors simulation)?

I am trying to simulate the behaviour of a Piezoelectric sensor, positioned behind a plate subjected to ad impact and consequential oscillations. I have set a transient analysis and associate the...

17 November 2020 3,377 3 View

It is possible to model piezo electric behaviour with Coupled Field Transient tool?

I am trying to model a piezoelectric sensor attached to an aluminum thin plate. I know that it is possible to model a PZT using Mechanical APDL, selecting the proper elements, such as PLANE13,...

13 October 2020 7,915 11 View