[Fluorolog 3 HORIBA] - How to fix jumps on the emission spectrum?

More Everton Bonturim's questions See All

What is the best book currently available on nanotechnology?

I would like suggestions for the best books on current nanotechnology. Does anyone know any good ones? Are there any that can be downloaded in PDF from the internet.

03 April 2014 8,258 2 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

Is it possible to have two luminescence bands of the same peak position but with different intensities in single spectrum??

Hi! If it is possible to have two luminescence bands of the same peak position in a spectrum, what is the reason behind formation of two separate bands instead of one? This phenomenon is related...

26 February 2021 4,963 5 View

How can I find a Raman spectrum wavenumber corresponding to what compound?

I have several Raman spectra with very distinct peaks at certain wavenumbers, such as 277, 359, 466, 583, 623, 686, and 795cm-1. How can I identify them to what compound(s)? The RRUFF and others...

24 February 2021 363 3 View

Is this the write procedure for acid digestion of soil for heavy metal analysis using AAS?

How to do acid digestion of soil sample with 3:1 aquaregia in an open vessel?

23 February 2021 3,053 7 View

How to constrain genetic algorithm input u?

My real system (buck converter) can only take an input of 0 to 1 (duty ratio) and I need to constrain the system so the controller action keeps within this bounds. How can I do this? The code for...

22 February 2021 2,125 3 View

What are difference between laser diodes, simple light emitting diodes and power light emitting diodes when operated in the visible spectrum ?

I want to illuminate a scene (small space) using LED to capture photographs or videos of some tiny objects inside the space. But am not sure if I should use a Laser LED, or simple LED or power...

22 February 2021 4,240 4 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

How can I simulate the optical absorption spectrum of a biomaterial (like DNA or protein) in COMSOL?

I need to simulate the optical properties of a biomaterial, namely DNA, in COMSOL. Basically I need to simulate the IR absorption spectrum of a cylinder filled with a 'concentration' of DNA. I am...

21 February 2021 3,043 3 View

Selvalakshmi Thangaraj

It is because different detectors are used to detect the wavelength of different range. When the range is shifted from one range to another, such jump will be observed. It will be uniformlly observed in all the spectra. you can see the attached spectra for reference.

Everton Bonturim

Dear Selvalakshmi Thangaraj,

I got it, but do yo think if is it possible somehow to remove those artifacts? I really do not wanna work with spectra which present "jumps" in the middle of collected range... specially if I have to integrate some peaks to compare intensities.

Thank you for your attention and contribution.

Best,

Everton