How to model Supercritical water gasification (SCWG) process in Homer software?

Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?

25 February 2021 4,075 1 View

Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software?

Hi every one Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software? Biogas fuel is not available in the options thanks

23 February 2021 6,518 3 View

How can I find the thermophysical properties of high temperature microencapsulated phase change materials (MPCM)?

Hi everyone. I am looking for a high temperature MPCM. More specifically, I need the thermo physical properties of a microencapsulated phase change material with the melting temperature between...

14 February 2021 3,606 2 View

Can explain this diagram to me, is this the average consumption curve for one day or the total consumption of days in a month summed up in specific?

The hourly load curves of the selected household in each season are shown in Fig. 28. Figure 28 shows the demand for electricity in four months on an hourly basis. Can you explain this diagram to...

08 February 2021 657 16 View

How can I find eddy size distribution in ANSYS Fluent?

Hi everyone, I'm simulating a 3D turbulent pipe flow using the SST K-W turbulence model in ANSYS Fluent. Is there any quantity among the postprocessing quantities that represent "eddy size" or...

01 February 2021 731 1 View

Is it possible to highly selective remove a fused silica template from PDMS by laser-induced backside wet etching (LIBWE) method?

Hi everyone I'm trying to pattern circular cross-section microfluidic channels in PDMS. The template is an optical fiber with an axially non-uniform diameter. To the best of my knowledge, there...

22 January 2021 2,352 2 View

How to match results from based paper and Ansys Workbench in modeling piezoelectric?

Hi guys, I have modeled a laminated composite beam patched with piezoelectric layers in Ansys Workbench, but the results are far away the results reported in base paper. I have attached the...

13 January 2021 7,356 3 View

What is the gradient thermal annealing (GTA) process?

Hello to all What is the gradient thermal annealing (GTA) process?

06 January 2021 7,740 2 View

What is the difference between organic perovskite solar cell and inorganic perovskite solar cell?

Hi everyone What is the difference between organic perovskite solar cell and inorganic perovskite solar cell? Thanks

01 January 2021 4,310 6 View

How to measure both Sulfites and Sulfates Ions In water?

Could you please help me to know a very simple method to measure the amount of Sulfite (SO3) and Sulfate (SO4) ions in the water? (titration preferred)

27 December 2020 9,350 4 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View

What's support me on Simulink Matlab Model of Regenerative Braking in DC Traction ?

I have a thesis on Utilize the electrical power from Regenerative Braking in 750 Vdc Traction by simulation in the Program MATLAB Simulink. I made the Power Load flow from 24kV to Traction...

08 February 2021 2,532 1 View

How to apply distributed load in a 2D model with plane stress/plane strain thickness in ABAQUS?

Hello all, I'm currently working on setting-up a 2D bone remodeling problem of a femur from literature. I take a 2D femur geometry and give it an out-of plane plane stress/plane thickness in...

06 October 2020 2,623 5 View

How can I create an environment in MATLAB or Python to test a traction control algorithm?

For a project I am working on I need to implement traction control to a RC car. In designing this algorithm I need to create a simulation environment in order to test the control algorithm. The...

24 April 2020 8,529 1 View

How can I build a stationary energy storage device for DC urban rail system?

Hello, I need to plan the capacity of stationary energy storage device for DC tram service, which has an acceleration current is almost 800A. And such 2 trams are running in one section, where I...

27 February 2020 1,406 2 View

Abaqus Analytical Mapped field not functioning properly?

Dear all, I am trying to use analytical mapped field in Abaqus to apply loading that I have calculated in a 3rd party software to nodes of my Abaqus model. My problem is that instead of...

30 August 2019 8,535 2 View

Abaqus Analytical Mapped field not functioning properly?

Dear all, I am trying to use analytical mapped field in Abaqus to apply loading that I have calculated in a 3rd party software to nodes of my Abaqus model. My problem is that instead of...

07 August 2019 9,901 2 View

What is the meaning of E/Enn in traction in abaqus?

Hello Guys I know so many of you have the same question when you start using cohesive element in abaqus. This section is a bit confusing E/Enn does not mean dividing. It simply means Young modulus...

07 August 2019 7,379 4 View

Boundary condition on a solid surface under traction/compression ?

Hello, I have a block of solid material in which an elastic wave is propagating. On one side of the block I maintain a static surface stress (the agent causing this stress is external to the...

18 July 2019 8,330 7 View