Electric filed calculation for specific value of PhaseX and PhaseY in dispersion diagram using CST?

25 February 2023 0 9K Report

Hello Everyone

I have simulated a dispersion diagram for first Irreducible Brillion Zone (IBZ) using CST as in the attachment. Now I want to check electric field for any specific value of PhaseX and PhaseY. Can anyone assist how can I check using CST?

Thanks,

Best thought.

Badges
Science topic

More Faizan Faraz's questions See All

How can we draw the adsorption isotherms of Langmuir and Freundlich together with the experimental data in a single graph on Excel?

Thanks in advance

22 December 2020 7,853 4 View

How to change the direction of polarization of incident wave?

How to change the polarization direction for the incident wave in CST to designing a metasurface unit cell? Will the change in polarization direction have the same or different output? I change...

20 November 2020 8,726 8 View

How to perform both heat and mass transfer analysis of aircraft engine in ANSYS FLUENT?

Dear All I need to perform the heat and mass transfer analysis of air craft engine. I want to know how to model IC engine and Fluent module combine. Can I perform both analysis in a single module...

13 September 2020 3,786 3 View

Clinical Trail: How can we justify statistically a CT when it fails at final stage?

When a clinical trail succeed in first trails and fails at final trail,please write me, how could we justify the cause behind its failure statistically.

10 August 2020 8,035 3 View

Can we use Ethanol Amine or Poly ethylene glycol instead of Oleic Acid to synthesize Molybdenum Disulfide (nano)? Either Yes or No, What is Reason?

I want to Synthesize Molybdenum Disulfide at Nano Scale. Can I use Ethanol Amine or Poly ethylene glycol instead of Oleic Acid? Please brief with the reason.

26 July 2020 913 3 View

How to get crackless and pinhole free SnO2 layer in perovskite solar cell?

I am making SnO2 layer by spin coating method using 3.75wt% SnO2 nano particles in DI water. The spin coating speed is 3000 rpm for 30 seconds. I am using low temperature annealing process method....

21 June 2020 658 15 View

I want to dissolve S and Mo precursor in organic solvents, can anyone guide me?

I tried with heating and without heating but it is not working. They are well mixing in DI water but not in organic solvents.

03 May 2020 3,819 7 View

Embryonic brain free floating 50um sections - immunofluorescence antibody penetration iba1/mounting question?

Hello all, I am having trouble with antibody penetration of Iba1 staining in my tissue, i can only seem to get about a 30-35 z-stack. Additionally I have a really hard time mounting this tissue,...

26 February 2020 8,170 5 View

How to treat 'deliberately missing' values for PLS SEM Analysis?

I have come across a situation regarding the application of PLS SEM for my research scenario. I have survey data of 213 respondents in total with Likert scale responses ranging from 1 (Strongly...

09 January 2020 9,847 2 View

Problem in Meshing using ICEM?

I am trying to mesh airfoil with flap with small gap between airfoil and flap using ICEM, and I am having this error while check mesh in FLUENT. I am doing structured meshing Minimum Orthogonal...

07 January 2020 522 5 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

Compact antenna for the frequency range 1 MHz-5 MHz?

Hello everybody! I have a problem with developing a compact antenna for the 1MHz-5MHz frequency range. Tell me what type of antenna can be used and what books and articles to read to perform this...

27 February 2021 7,710 4 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View