Effect of pressure on flow rate of polyester?

More Ashifat Olawumi's questions See All

Request for Response to a Survey?

Dear Sir/Madam, Hope you are doing well. I need your help on a questionnaire survey related to BIM & Sustainable practices in the Construction Industry that I'm conducting. You can either make...

04 October 2017 7,747 6 View

What is the effect of PEDOT:PSS on the environment?

i want to know if PEDOT has good effect on our environment.

08 April 2016 5,950 1 View

Which is the best way to get rid of copper residue on the back side of wafers following plating even after bevel edge clean and backside clean?

Following electroplating of Cu, residues of Cu are seen on the backside of the wafer. Bevel edge clean and backside clean seem to make it worse. Probably increases the roughness of the backside...

20 February 2015 8,890 3 View

What could be responsible for arcing during via etch in a vacuum chamber?

During BEoL via patterning, arcing is observed sometimes to the point of wafer breakage(seal band arcing). Failure analyses show craters at the point of the arcing. These craters appear at other...

11 February 2015 3,304 12 View

..choosing optimal lag for a model is an empirical issue! What is your opinion?

Although decision on this can be guided by the rule-of-thumb that says you choose the model that gives the lowest values among the criteria (i.e. Akaike, Schwarz, etc).

01 January 1970 3,199 1 View

𝐵𝑙𝑜𝑐𝑘𝑐ℎ𝑎𝑖𝑛 𝑉𝑎𝑙𝑢𝑒 𝑀𝑜𝑑𝑒𝑙 (𝐵𝑉𝑀) 𝑓𝑜𝑟 𝐶𝑜𝑛𝑠𝑡𝑟𝑢𝑐𝑡𝑖𝑜𝑛 𝑆𝑢𝑝𝑝𝑙𝑦 𝐶ℎ𝑎𝑖𝑛: Survey invitation

We are conducting a research project on "𝐵𝑙𝑜𝑐𝑘𝑐ℎ𝑎𝑖𝑛 𝑉𝑎𝑙𝑢𝑒 𝑀𝑜𝑑𝑒𝑙 (𝐵𝑉𝑀) 𝑓𝑜𝑟 𝐶𝑜𝑛𝑠𝑡𝑟𝑢𝑐𝑡𝑖𝑜𝑛 𝑆𝑢𝑝𝑝𝑙𝑦 𝐶ℎ𝑎𝑖𝑛" and currently seeking to leverage your knowledge and experience 𝑖𝑛 𝑒𝑖𝑡ℎ𝑒𝑟 the construction...

01 January 1970 662 10 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

Wrong out put for gmx x2top?

Dear users, I would like to simulate a zeolite structure in gromacs. I got the .cif file from IZA expanded in one direction in Materials Studio and exported a .pdb file. However, when I want to...

24 July 2024 367 4 View

Edwin A. Murillo

I think that there is not significative effect of the pressure on flow rate under oscillatory conditions in rheological analysis.

Khaled Elnagar

Pressure is directly propotional to flow rate under all conditions if its in duct...but if you talking on pressure in static condition the reverse is true

Jagadish Nayak

please explain mathematically

There are many puplications on tbe rheometry dealt with the theoritical mathematics