During Solvent casting process,if we use different solvent for a single polymer,is there any physical or chemical property will vary or not ?

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

What solvent can I used for Paal Knorr reaction between 6-amino hexanoic acid and 2.5 hexanedione?

I am try to make the Paal Knorr reaction between 2.5 hexnedione and 6-amino hexanoic acid, my problem is type of solvent to use, because 6-hexaminohexanoic acid is soluble in water but I am not...

02 March 2021 4,443 2 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

How to polymerize TEOS?

I want to polymerize TEOS on a surface. I know that NH4OH is a preferred catalyst and an alcoholic solvent should be used .But I can not find certain amounts of each material to use. Does any one...

02 March 2021 1,404 6 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Ester cleavage conditions?

Hi all, I need to cleave the ester in Ethyl 2-amino-1H-imidazole-5-carboxylate to make the carboxylic acid and retrieve the product from solution to use in downstream applications of linking to...

01 March 2021 8,766 3 View

How can extract ciprofloxacin hydrochloride disolve in water er to organic solvent such as dichloromethan or any other solvent?

I need a procedure to extract the ciprofloxacin hydrochloride from aqueous solution by using dichloromethane in detail,. I thank you very much.

01 March 2021 4,306 1 View

Rinkesh Bhatt

Dear Nayak,

Yes. The structural parameters are widely affected i.e physical parameters. I attached my research work in this regard.

Best of luck.

Gyorgy Banhegyi

If the solvent casting involves phase separation , you may expect wide differences. The same is true if you cast semicrystalline polymer films. The amount of residual solvent may also be different.

Dr. Banhegyi,

Please explain phase separation in the polymerization of monomer with the solvent and than again same polymerization of monomer with the other solvent by solvent casting process.

With regards.

Ratikanta Nayak

Thanks to Rinkesh ji & Gyorgy sir for your reply.I think here phase separation means, Due to long relaxation time and large scale of polymer molecules, the morphology of phase separation in polymer systems can exhibit many special features such as volume shrinking and phase inversion phenomenon compared with that in small molecule system.