Effect of tackifying resin mol. wt. on tackiness of a Adhesive
Dear Asit Baran Bhattacharya, for linear (noncrosslinked) polymers, MW is the most operating parameter, providing chain mobility at the interface is not restricted. Please check the following papers. My Regards
https://doi.org/10.5254/1.3536010
https://doi.org/10.1021/ma0020279
I am planning to prepare a decellularized porcine tissue derived biomaterial. It would be very helpful if I get to know the composition of the solution which is ideal to bring the tissue sample...
31 July 2024 5,645 2 View
Difference between Radial and Linear SEBS, in view of processing and properties.
21 June 2024 2,927 0 View
Hello, I have a question regarding fluorescence intensity measurement in imageJ software. The tutorials provide different methods, the simplest one is to use a fixed ROI and measure the mean gray...
20 February 2024 752 0 View
I am trying to dissolve the PS beads in MS media as a treatment to plants. I can not make a suspension. I also require to measure Zeta potential of the PS beads, but the DLS analysis needs a...
04 February 2024 5,098 11 View
Hi , My over all experimental goal is to define Zika virus-specific T cell responses in macaques infected with Zika virus. We also have control macaques that were not infected with Zika. We used...
16 November 2023 5,546 0 View
It is very evident so far that although there are multiple conservative treatment for shoulder pain starting from medication to intraarticular injections to physiotherapy or naturopathy but none...
14 September 2023 6,588 7 View
What is the effect of di-block content (sis) on tackiness of a holt-melt adhesive....effect of viscosity and mol. wt. on tackiness & rheology
12 August 2023 6,351 0 View
Can higher exposure to UV radiation of my gel which I need to cut and purify create mutations for further use?
06 August 2023 7,620 0 View
When checked in enzymatic assay, a compound with IC50 37 nM showed a KD value of 20 µM against ITC. How can this discrepancy be explained?
17 July 2023 3,515 1 View
I have synthesized a racemic compound and its two enantiomers. The IC50 value of racemic compound is 2.4 μM, for R is 1.1 μM and for S is 0.5 μM against the target protein. How to explain the...
08 May 2023 1,622 1 View
Hello everyone, I am currently working on a protein that is 10x his-tagged and positively charged (predicted pI=10.16). But when I tried to use Ni-NTA column to purify the protein, it's not...
24 July 2024 7,293 4 View
The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.
23 July 2024 3,205 0 View
Hello, I am experiencing an issue with mixing micro powder with resin in a 3D printer. The problem is that sedimentation occurs after a short period (about half an hour to an hour). Could you...
23 July 2024 1,672 0 View
https://en.wikipedia.org/wiki/Viscosity
21 July 2024 3,089 4 View
So i have a few peptides (synthesized by SPPS and not cleaved from resin) and I want to add a maleimide label. We have NHS-PEG-Maleimide and from literature it is evident that the free amine group...
18 July 2024 4,075 3 View
Good day everyone, Trying to perform protein purification for the first time, gotta buy the whole equipment/reagents. Protein of interest 48 kDa (Antithrombin), expressed from his-tagged plasmid...
16 July 2024 3,692 6 View
as of my knowledge z90 is acrylic based sealant adhesive.
09 July 2024 8,660 4 View
Even adding fragrance is not working
05 July 2024 741 2 View
I want to close crack in alumina kindly suggest any glue or epoxy to close leak.
27 June 2024 10,110 1 View
In the molecular dynamics simulation analysis part, how to calculate molecular surface area (MolSA) and polar surface area (PSA) in gromacs ?
14 June 2024 1,469 1 View