Does anyone know how to implement the burner control (for industrial boilers) in Matlab or any easy way?

More Osama Abd's questions See All

How can I implement and simulate a wireless sensor network in Matlab?

see above

01 February 2014 4,557 13 View

Does anyone know how to implement the LVDT sensor in Matlab?

see above

01 February 2014 5,383 2 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What are the most reliable approaches to extract key continuous frames from a video, with complete automation?

I have an input video, of skin (from a microscope that means it is magnified such that blood capillaries are visible). The idea is to extract 15 sec of continuous frames from a video of 1 min,...

02 March 2021 2,735 2 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Isolates of Hymenoscyphus fraxineus?

Dear Dr. Cai, my name is Simone Prospero and I work in the team of Phytopathology at the Swiss Federal Institute for Forest Snow and Landscape Research (WSL;...

01 March 2021 1,133 1 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

Zol Bahri Razali

The easiest way is used solidwork software, then you can shows it in multimedia

Osama Abd

Thanks Bro, for your reply

Marek Mazur

Maybe you should consider using LabVIEW. Combined with an acquisition and control system from National Instruments you can easily control the industrial boiler by reading and controlling their electric voltages