I am using ammonium salt of sulfosuccinate surfactant for the polymerization of SA emulsion polymer.
I am finding it to be an incompatible system while processing thermal initiator water based emulsion polymerization.
Dear Vipul,
Please refer first to: W. Breuer, R. Höfer, Sulfosuccinates for Emulsion Polymerization, Tenside Surf. Det. 40, 208-214 (4/2003) and the literatue cited there.
Best regards
Rainer
---------------
Dr. Rainer Höfer
Editorial Ecosiris
Klever Str. 31
D- 40477 Düsseldorf
Tel.: +49 (0) 211 4920479
Fax: +49 (0) 211 4920477
Mobile: +49 (0) 172 2418861
E-Mail: [email protected]
www.ecosiris.eu
Anybody knows interaction between Oxo alcohol & fatty alcohol ethoxylates surfactant chemistry for polymeric synthesis and coating application
10 November 2014 9,872 0 View
If we are using a combination of surfactant for synthesis, is there any control or calculation to control overall acid value?
31 December 2013 7,320 0 View
Require sophisticated ready setup supplier and manufacture for conducting pilot scale up within safety norms.
09 October 2013 8,716 0 View
Working over designing for pressurized reactor designing.
06 July 2013 8,692 0 View
Analysing effect of pKa of carboxylic groups during synthesis of emulsion polymerization.
03 April 2013 2,863 1 View
Can surfactant pH plays any role in this case
03 April 2013 2,547 0 View
Working on compatibility of different monomers with each other for coploymerization
09 October 2012 3,720 4 View
I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...
08 August 2024 8,329 0 View
I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...
30 July 2024 6,420 1 View
I have multiple small samples of grass pollen with anthers. I want to find a method to identify concentrations of proteins, lipids, and other various elements for these samples. any suggestions?
28 July 2024 5,331 1 View
Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...
27 July 2024 5,748 0 View
It has been long known that EDC carbodiimide and NHS easter's half life agains hydrolysis are highly related to pH. However, very surprisingly, not yet found a paper giving a table/chart of their...
25 July 2024 8,738 0 View
I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...
23 July 2024 9,938 1 View
Hi, I am a PhD student working at Jagiellonian University, Faculty of Chemistry. My work is related to the development of new analytical methods for the quantification of short-chain fatty acids...
22 July 2024 5,492 6 View
I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...
21 July 2024 1,559 1 View
Suggest the best and shortest route for the chemical synthesis and and green synthesis of magnetite(Fe3O4) The chemical synthesis should contain the least dangerous chemicals along with full...
21 July 2024 2,476 2 View
Dear Researchers, My question is associated with the "MDCI" method in Orca. Please let me clarify my question using a simple example: Suppose we are going to perform CBS extrapolation using "!...
21 July 2024 1,632 0 View