How to visualize stress in a coating defined by "Skin" in Abaqus?

Hello All! I'm trying to model a contact between a coated substrate and a tip in Abaqus. The coating is ultra-thin compared to the geometry of the substrate. So I defined the coating using the...

16 February 2021 1,594 3 View

Is a Strong correlation between the Moderator variable and the dependent variable an issue for moderation model (model 1) in Hayes PROCESS?

In a typical moderation model with one moderator, is it a problem if the moderator and the dependent variable show a strong correlation (say 0.85)? What if a strong correlation exists between the...

27 January 2021 4,937 4 View

Which syringe filters (e.g., PTFE, MCE, PVDF, CA, PES, etc.) are the best to filter TBS/PBS buffer (pH 7.5-8.5) and glycine buffer (pH 2-3) solutions?

I intend to purify antibodies from serum using the affinity procedure, and I need to filter the binding (TBS/PBS) and elution (Glycine) buffers before applying them to my solution.

06 January 2021 5,769 3 View

Gear reduction for back-drivability of a motor?

Hi everyone, Does anyone know up to what reduction ratio of gear does a motor remain back-drivable? I want my robot to have safe interactions with the environment and other humans. Can you give a...

26 December 2020 7,142 3 View

How to export DigSilent Plots with high quality?

Hi all; I've started using DigSilent these days. However, I'm wondering how can I export the results with high quality the same as MATLAB plots as I currently do. Thanks

19 December 2020 2,666 2 View

How to assign initial stress to a coating in Abaqus?

Hello! I am trying to define/assign initial stress to a coating I modeled on a substrate. I defined the coating using "skin" function. I have tried "predefine filed" in load section. But it only...

10 December 2020 2,921 8 View

How to model a multilayer coating in ABAQUS?

Hello! I'm trying to model a multi-layer coating on a substrate in abaqus. The layers are homogenous and isotropic. My question is how should I approach the modeling? WHAT I'VE TRIED SO FAR: I...

09 December 2020 1,235 3 View

How can I calculate Nusselt number by using this equation (Nu = ht.gradTx * nx + ht.gradTy * ny + ht.gradTz * nz) step by step in COMSOL?

Calculate the Nusselt number using the COMSOL Program

09 December 2020 3,354 3 View

How to calculate sulfur loading of lithium -sulfur batteries using Li2S8 catholyte?

I am gonna use Li2S8 catholyte to introduce active material to cathode instead of using sulfur. May anybody kindly guide me about the way I can calculate the amount of sulfur (g/cm2) loaded on the...

07 December 2020 7,556 2 View

How to great data visualization and what example for it ?

i need explain data visualization and what type it and how great it by excel or other program > paper attached for help

30 November 2020 1,159 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View