Dear altruists, which US universities you will recommend for a PhD in power and energy studies?

More Farihal Abedin's questions See All

Can the debye temperature calculated using elastic sound velocity be used in Slack model to find Thermal conductivity?

I am trying to calculate lattice thermal conductivity using Slack model. In Slack model the lattice thermal conductivity is proportional to (Debye temperature)^3. Can I use the Debye temperature...

11 June 2024 1,719 1 View

How to solve a PDE numerically taking another equation also as boundary condition?

Suppose, we need to solve 1D heat conduction equation numerically to simulate the heat transfer for a steel rod where convection occurs at its surface. Now, how to solve the 1D heat conduction...

27 December 2023 2,149 2 View

Who is interested in collaborating on a PhD thesis in the field of ethical consumption?

Hello I have a PhD student from Iraq. her thesis subject is "Customer purchase intention in Iraq: a study in the field of Ethical consumption". The purpose of this study is to discover the complex...

30 August 2023 2,050 5 View

Who is ready to help me?

I am looking for a colleague to carry out valuable academic research (In the field of increasing the quality of managers' decision-making) with the following conditions: - University faculty...

25 May 2023 7,929 1 View

Would anyone cooperate with me in conducting a cognitive research on managers?

Hello dear colleagues I am conducting an experimental research on the effect of neurofeedback training on the decision-making speed of managers in a situation of harm. Does anyone cooperate with...

16 May 2023 9,413 2 View

Why tensile properties decreased while flexural properties increased?

I am currently studying the effects of mechanical properties of GO and rGO on PC/ABS. However, after analysing the data, I found that the tensile strength decreasing, but, for the flexural...

12 March 2023 9,883 3 View

How can I disperse C3N4 nanosheets?

After sonicating, my solution precipitated, pleased help me.

13 August 2022 7,313 0 View

How to apply a particular strain on a cubic compound using Materials Studio?

I have tried changing the lattice parameter using this formula: a2 - a1/a1 where a1 and a2 are unstrained and strained lattice parameter after full geometry optimization. Problem is...suppose I...

21 July 2022 9,181 3 View

How to create van der Waals heterostructure in Material Studio?

I want to create a van der Waals heterostructure from two monolayers in Material Studio. How can I do that?

15 May 2022 4,770 1 View

What is the explanation for band structure without high symmetry points and all bands displaying straight lines?

When I calculated the band structure pristine ZnO monolayer, I got band structure with high symmetry points. But when I tried calculating the band structure for doped g-ZnO with same brillouin...

06 May 2022 7,586 2 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Smart grid ideas?

How to use and this is economical?

06 August 2024 3,160 2 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

How to conduct a sensitivity power analysis for Kendall's Tau?

Is there a straightforward way to conduct a sensitivity power analysis for a Kendall's Tau correlation? I was considering using the sensitivity setting and "Correlation: point biserial model" test...

28 July 2024 6,133 8 View

Terrorism, a natural inclination of all animal species?

There are many types of symbolic judgements. For example, when an Israeli pilot flattens the home of a Palestinian family (even if they are forewarned), it is natural for them to experience shock...

28 July 2024 2,610 1 View

Can anyone help me with in providing the procedure for purification of GSTtagged protein by gst affinity chromatography without an automated machine?

Purification of gst tagged protein

25 July 2024 1,720 0 View

Niranjan Kumar Mandal

MIT, CENTRAL UNIVERSITY, FLORIDA, HARDVARD UNIVERSITY

Hassan H. Eldeeb

Georgia Tech, UCF, U of Wisconsin, MIT, Virginia Tech, Carnegie melon, U of Illinois UC, Florida International University

Asaad Mohammad

Georgia Tech, Texas A&M, IIT Chicago, Carnegie melon and the ivy leagues one.

I would suggest first to secure support from potential supervisors then decide which one to join.

Ashok Kumar Tripathy

Adequately answered. One can try the next layer like California state univ, or some of the canadian univ , western ontario etc