CST I-solver: Why the normal type materials are not meshed in I-solver? it says just PEC materials are considered for meshing.?

More Parisa Lotfi's questions See All

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

Can the Dunn's test be used as an appropriate post-hoc for the G-test?

Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...

23 February 2021 5,827 3 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

Where can the fault diagnosis data set of lithium battery be found?

Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...

21 February 2021 8,659 1 View

How to define the sink temperature and film coefficient?

Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...

21 February 2021 6,197 1 View

How to discriminate between Sentinel-2 Level-2A Product Discriminators?

According to the Sentinel-2 user guide here (https://sentinel.esa.int/web/sentinel/user-guides/sentinel-2-msi/naming-convention), the compact naming convention is arranged as...

21 February 2021 5,919 9 View

Are ZnS nanoparticles moisture sensitive?

Hello Everyone, I tried to form ZnS nanoparticles using the hot injection method and was able to form the same (confirmed by XRD). When I centrifuged, after the reaction I got a kind of white...

17 February 2021 1,709 3 View

Can anyone suggest a software for running a plant tissue culture lab?

A software which can help to design the experiment, store data, update new data, set subculture reminders, barcoding etc. Like Invitrosoft.

17 February 2021 3,015 5 View

Is an encrypted dataset with Microsoft SEAL compatible with Cloudsim simulator??

Hello, I would like to do homomorphic encryption using Microsoft SEAL on my dataset and then use it as an input to the Cloudsim simulator to do clustering on. Is it possible and compatible with...

16 February 2021 3,915 1 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

Compact antenna for the frequency range 1 MHz-5 MHz?

Hello everybody! I have a problem with developing a compact antenna for the 1MHz-5MHz frequency range. Tell me what type of antenna can be used and what books and articles to read to perform this...

27 February 2021 7,710 4 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

Is there a way to use waveguide ports for circular antenna design in CST?

Hi, whenever i use circular array i get this error "Waveguide ports must be aligned with Cartesian coordinate planes for the transient solver" Does anyone use circular array with waveguide ports?...

09 February 2021 3,609 8 View

How to model in HFSS or FEKO Free Space Material Characterization?

I am having trouble setting up this problem in HFSS or FEKO. In HFSS, I've tried both FEM and FEBI-IE solvers. With FEKO, I've tried it's MoM solver and default settings. I am would like model...

09 February 2021 375 2 View

What is best solution for optical metamaterial design calculation: HFSS, COMSOL, CST?

Dear all, Now I'm selecting FEM for design of metamaterials on NIR~VIS frequencies, and keeping 3 software: ANSYS HFSS, COMSOL with wave optics module, and CST STUDIO SUITE. Could you give me...

09 February 2021 9,517 2 View

Which journals (Q1,Q2) accept simulation based design and results of antenna if fabrication and testing facility is not available?

I need a list of good (preferably Q1,Q2) journals that will accept research papers prepared on designs done with the help of simulation software e.g CST, HFSS etc.

08 February 2021 9,636 5 View

How to achieve the sensitivity diagram of a sensor in CST?

I wanna design a sensor in CST 2021 for the first time and I don't know how to achieve the sensitivity diagram of the sensor in CST. Could you plz help me to do that? I appreciate your response...

26 January 2021 6,864 1 View

What is corrct way to define ports when simulating FSS and surface waves in CST?

I need to simulate a mushroom FSS and I'm struggling with the ports. What's the correct way to define them? Should I construct a proper SMA connectors, or is it enough to put a waveguide ports...

19 January 2021 6,590 4 View

Malcolm White

The brochure says it is a surface mesh, not a volume mesh. It also says it does PEC and lossy dielectric materials.

https://www.microwavejournal.com/ext/resources/BGDownload/d/e/CST_STUDIO_SUITE_Isolver_low.pdf?1326826565#:~:text=CST%20MICROWAVE%20STUDIO%C2%AE's,and%20radiation%20pattern%20analy%2D%20sis.

Parisa Lotfi

Malcolm White Yes i need a surface mesh for a component which is not PEC. Do you have any suggestions?

No I don't have an answer, but the information in the brochure means that there will be some way of doing it, so it's worth keeping on looking.