Hi,everyone.
How do I estimate the natural frequencies(coupled) of piston and sloshing motion inside a moonpool in a ship which is free to heave and pitch..?
Hi, you can find answer from the book of Odd Faltinsen -- 'Sloshing'.
Thank you very Sir.
It must be there in our Institute Library.
I will check it.
Please refer to the followings.
Basically, sloshing-mode and piston-mode moonpool resonances depends on the shape of moonpool.
- For plain moonpool (simple square) -
1. Fixed condition - B.Molin's theoretical formula.
2. Floating conditioin
- Fukuda's empirical formula and other research work.
- Experiment (full frequency range)
- From potential based motion analysis results, you can find resonance frequencies(piston-mode, sloshing-mode) from the peaks in surge and heave RAO.
- CFD simulation (full frequency range)
- For the model with cofferdam (or called recess deck)
1. From potential based motion analysis results: the peaks in surge and heave RAO.
2. Experiments (full frequency range)
3. CFD simulation (full frequency range)
Thank you.
Hi Seung,
Thank you for your reply. Yeah, I have all the references mentioned by you with me. I will revise them.
Dear researchers, I tried and understood that PLA dissolves well in the solvent mixture of DCM and Ethanol. It also dissolves well in DMF, Acetone, THF and Chloroform efficiently. But does anyone...
23 April 2024 6,622 4 View
Dear all, I am using AutoDock Vina to obtain the binding free energy of a ligand and a crystal surface. Using ADFR suites to convert input file from pdb to pdbq, I use prepare_receptor -r...
04 December 2023 9,970 0 View
Hey guys, I tried electrospinning PLA nanofibers on aluminium foil. I was able to achieve thicker fibers by increasing the viscosity of the solution. However, the fibers stick to the aluminium...
03 December 2023 3,417 5 View
Hey guys, By tweaking the viscosity of my polymer solution, I was able to obtain thicker PLA films after electrospinning. However, I am unable to separate the PLA polymer film from the aluminium...
14 November 2023 2,188 2 View
I have heard certain good things about Metal Injection Moulding, specially the fact that it can produce very accurate parts. Moreover, it also makes the manufacturing of complex- design parts look...
29 October 2023 956 0 View
Hello everyone, I electrospun the PLA fibers onto the aluminum foil. Upon drying in air, the PLA fibers stuck onto the aluminum foil and am unable to peel them off for further characterization....
26 September 2023 9,187 0 View
Hi guys, Upon searching the literature, I found that DCM and DMF were the most commonly used solvents for electrospinning PLA polymer. Can you please tell me what other alternate solvents can I...
13 September 2023 7,507 4 View
Hello everyone! I have interesting question asked by my professor and I could not find relevant answer anywhere. Why are we seeing up and down pattern on transcript abundance? Example RNA seq data...
19 January 2023 9,289 4 View
I have used wet samples and dried film samples for Tg in DSC but I could not get any major peak.
04 August 2022 8,714 2 View
Supposing that a cooling tower is installed in a region which is extremely humid. Given the fact that the wet bulb temperature will be high, in these type of conditions, the delta T between the...
28 June 2022 8,055 0 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
It is important to highlight that technological surveillance on oceanographic vessels is a collaborative effort in which different specialists work together to effectively leverage technology in...
31 July 2024 1,633 0 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids
28 July 2024 4,985 1 View
Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...
28 July 2024 5,771 2 View
Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?
27 July 2024 648 3 View
Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...
25 July 2024 9,058 4 View
// interested in the difference between floating events and short circuits.
22 July 2024 6,565 0 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View