Could anyone help me on "polyethylene of raised temperature resistance,(PE-RT)"?

More Maziar Dehghani's questions See All

How do you characterize resin and rosin by FTIR?

How could we distinguish between resin and rosin in an FTIR diagram? Also, how could we calculate the ratio of C5/C9 in resin, by the usage of FTIR?

10 November 2014 9,119 1 View

What does waterborne structure mean for polymers?

what does waterborne structure mean for polymers?

10 November 2014 5,540 4 View

What is the quickest method for silane grafting measurement in polyethylene?

The polyethylene which has been grafted by silane was cured and then by the usage of gel test, its approximate silane grafted can be distinguished! This method needs about ten hours and this is a...

06 July 2014 7,457 3 View

What is the effect of miscibility of LDPE/HDPE blend on its silane grafting?(Is miscibilty necessary for silane grafting?)

LD and HD are miscible typically, but by the change in some molecular properties of LD(such as their short chain branches content and ...),its miscibility would be affected. I want to know the...

05 June 2014 7,205 7 View

How can we understand the long term mechanical behavior of our blend or compound (as an example during 50 years)?

For example a LD/HD blend or filled polyethylene

05 June 2014 10,012 8 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How to increase simulation box size?

We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...

08 August 2024 4,842 0 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Are there instances where molecules with larger molecular weights exhibit greater mobility than those with smaller molecular weights?

Hi, I know that low molecular weight (MW) molecules generally tend to have higher mobility, while high molecular weight molecules tend to have lower mobility. However, in my experimental...

06 August 2024 1,495 2 View

For an in-vitro drug release study, what molecular weight cut-off (MWCO) dialysis bag is required for a 117 kDa protein?

kindly reply me. Thanking you in advance.

05 August 2024 7,727 4 View

Gyorgy Banhegyi

Pls find attaced some references

http://www.china-goffen.com/doce/new_look.asp?index_x=2&P_ID=76&c_ID=3&proname=

http://en.sdrtgc.com/products_detail/&productId=26.html

https://www.plasticpipe.org/pdf/pe_rt_new_class_polyethylene.pdf

Maziar Dehghani

Dear Dr.Banhegyi

Thanks for your help. but I need more information on its synthesizing.

Regards

Maziar

Dear Dr. Sanchez

Thanks for your helpful answer