The contact region in OTFTs is seen as a fundamental part of the device which is sensitive to physical, chemical and fabrication variables. can we reduce this effect to zero influence?
A bunch of flower for everybody. I would like to ask about the list of journals which we can publish our paper for free. Thanks in advance. Sincerely Walid
25 February 2021 9,790 3 View
Hi there! My lab has been brought an array of C-4 I cell line. The cells did not succeed in attaching to the bottom of the flask and remained floating in the media. Although we followed the...
04 February 2021 10,018 5 View
What is the p-type organic semiconductors having the highest mobility and high environmental stability?
21 December 2020 9,019 2 View
hi everyone, I have developed a simulation of a roundabout with a fixed time regulation, the lines of traffic lights in the roundabout are for vehicle storage. my question is: when we regulate by...
16 December 2020 1,923 3 View
Hello everyone, hope you are doing well. I made a simple traffic actuated control logic using VisVAP Stage 1 is for Vehicle Stage 2 is for Ped the compilation in VisVap run with success, but...
07 December 2020 553 3 View
24 October 2020 9,262 7 View
There are many universities that have excellent scholarship opportunities for international students.
21 September 2020 3,391 4 View
good morning, I found some difficulties to identify a compound extracted from a medicinal plant and analyzed using LC-MS/MS. I can't find the compound name in databases peaks (m/z) and intensity...
15 July 2020 5,669 3 View
According to the characteristics of each
21 March 2020 307 8 View
Our project objective is to investigate the genetic diversity of Palestinian date palm, cultivars. 6 primers were ordered, these primers were designed specifically for NGS analysis. DNA was...
06 February 2020 695 2 View
I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...
03 March 2021 1,931 5 View
I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...
02 March 2021 1,408 1 View
How do I do energy minimization in lammps with NVT ensemble ? I am using the following command and it does not seem to work. It stops at extremely high energy and gives me the error zero search...
01 March 2021 2,294 3 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
When explaining substitution models, the substitutions are expressed as Q matrix. Why is the sum of the elements in a row zero?
28 February 2021 3,864 3 View
What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?
28 February 2021 6,516 5 View
I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...
26 February 2021 1,511 3 View
Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...
25 February 2021 8,749 6 View
I am refining my XRD data using in FullProf program. The intensity of the modulated X-ray peaks is almost flat. I tried to adjust the peak intensities but unsuccessful. What is the reason? I guess...
23 February 2021 2,304 4 View
I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...
23 February 2021 9,592 2 View