i want to find Li distribution in my grains by doing line scan.
If you have a good EDS detector and a lot (really a lot) of Li, you can detect it. No quantification.
https://www.cambridge.org/core/services/aop-cambridge-core/content/view/S1431927613007678
https://www.oxford-instruments.com/products/microanalysis/energy-dispersive-x-ray-systems-eds-edx/eds-for-sem/silicon-drift-detector-sdd-x-max-extreme
I have plain strain compressed AA1050 Aluminum,in which i observe slip bands in deformed condition.I have done SEM and EBSD of samples.I want to know the slip systems active in a given grain.
02 March 2019 1,409 3 View
I want to know the procedure and minutiae to measure the SFE of Al-alloys by XRD .
31 December 2017 3,542 0 View
I want to do ZAF correction in eds or wds so that i can know correct percentage of elements in my sample.
01 February 2017 9,295 0 View
I want to find near boundary gradient zone for my samples,I tried using point to point misorientation from profile vector,but i am confused about criteria of NBGZ.
11 December 2016 4,302 4 View
I want XY data set from my EBSD scan to reconstruct the grain in a matlab code but I am unable to do it.
03 April 2015 3,264 6 View
I have 70 percent cryo-rolled 2219 samples but i am not able to get good scan from EBSD,what should I do?
01 January 1970 1,926 9 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am experiencing this for the Bi2Se3 sputtering target. Initially, even if the target was 2:3 in Bi : Se, with a few sputtering runs, due to the high escaping tendency of selenium, the top layer...
23 July 2024 1,649 1 View
I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...
21 July 2024 1,559 1 View
Dear all, I have a difference in the weight ratios between EDS mapping. What should I rely on? Is there a way to solve this problem?
12 July 2024 305 1 View
We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...
12 July 2024 2,768 1 View
Recently, we measured EDX/EDS of LaCrO3 crystals synthesized by hydrothermal method, and found that the characteristic energy for La and Cr are nearly the same for all of the noted energy levels....
02 July 2024 4,587 6 View
Hello I have prepared metal nanoparticles and did zeta potential. Normally there is a single peak in sample but now there are 3 peaks. I prepared sample for analysis first I prepared 10 mg/mL...
30 June 2024 1,063 4 View
Hello everyone, I'm facing an issue with EDS software that prevents me from obtaining atomic or weight percentages for my scan. However, I do have access to the raw data, which shows intensity vs....
29 June 2024 6,664 14 View