Genescan gives 3 peaks instead of one?

Hi all, I am doing a genescan analysis for a deleted exon in the patient sample. The amplified region is 215 bp. In the patient sample because of homozygous deletion, no peak is observed while in...

23 February 2021 5,645 1 View

How to extract water soluble amino compound from after aqueous work up?

4-Dimethyl amino pyridine is used in reaction.Product formed contains amino group along with amide & is highly water soluble. To remove 4-DMAP aqueous work up done. Please give solution. Thanks.

21 February 2021 1,883 1 View

How can I make a center of mass vs time graph?

I have a trajectory file of about 1000 frames which I have calculated a center of mass for each frame. I would like to use the first frame as a reference and see how much the center of mass...

04 February 2021 5,774 1 View

How doping in nano-particles with same valency affect it's crystal lattice structure?

When doping in case of semiconductor is concerned, we doped Si by trivalent or pentavalent impurity atoms to improve its electronic properties but in case of nano-particles, sometimes we doped...

31 January 2021 7,128 1 View

How to prevent aggregation of nano-particles without using surfactants?

As it is well known fact that nano-particles can easily aggregate during nucleation/ synthesis part due to high surface energy..by reading literature, I came to know that surfactants can help to...

30 January 2021 8,206 6 View

How do I dissociate an antibody used for positive selection of cells in order to re-culture the selected cells?

Hi, I am interested in cells that express a specific receptor. I use a fluorophore-conjugated antibody bound to the receptor followed by MACS positive selection to enrich for this...

21 January 2021 2,245 3 View

Is it possible that insecticides from same group and same mode of action may not show cross resistance?

I could not find any cross resistance between two insecticides from OP group, is this possible?

14 January 2021 9,625 3 View

I'm getting same +ve and -ve value of the blank, which I set for taking fluorescence reading?

I'm checking fluorescence of umbliferon and has set water as blank in two wells. The two wells are showing same reading but one is +ve and another is -ve. Also, the fluorescence can't be negative....

12 January 2021 2,332 3 View

Standard curve for 7 hydroxy coumarin (umbliferon)?

Hi! I am getting a higher fluorescence value for a lower concentration Umblifero solution than compared to a higher concentration solution. I am using the 0.001, 0.0008, 0.0006,0.0004, and 0.0002...

07 January 2021 4,353 5 View

I want to use Gold electrode as a reference electrode for electrodeposition of nanostructures. Can i use it and how ??

How to use a Gold electrode as a reference electrode ??

04 January 2021 4,058 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View