Best UV Stabilizers for HDPE?

More Shan Faiz's questions See All

How to calculate Force 'F' in formula u = F/W ??

I am looking to calculate coefficient of friction between a pallet and metal surface. If I apply u = F/W, how will I calculate F practically ? Alternate, is there any other way (instrument) to...

03 April 2019 9,947 2 View

What properties to look in magnesium hydroxide?

Hello Fellows .. I am working on a plastic pallet (not pellet) and my intention is to make it flame retardant. For this purpose I am incorporating Magnesium Hydroxide. Can someone guide me the...

06 July 2017 3,288 4 View

How can we improve(or create) an adhesion between Sand and PE in composite ?

In Sand/PE composites, can we apply any surface treatment to increase the strength? any suggestions? any other methods?

04 May 2016 5,759 7 View

Which are most effective impact modifiers for HDPE ?

I am looking for impact modifiers which are proven to be economical and best for HDPE. Note that I am preparing HDPE - Silica composites with blowing agents.

11 December 2015 8,456 4 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

Inquiry on Maximum Nucleic Acid Volume for 2.5 mL Liposome Solution?

I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...

30 July 2024 6,420 1 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

EDC carbodiimide and NHS easter 's half life among different pH?

It has been long known that EDC carbodiimide and NHS easter's half life agains hydrolysis are highly related to pH. However, very surprisingly, not yet found a paper giving a table/chart of their...

25 July 2024 8,738 0 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

How to eliminate the carry-over effect in GC-MS/MS system?

Hi, I am a PhD student working at Jagiellonian University, Faculty of Chemistry. My work is related to the development of new analytical methods for the quantification of short-chain fatty acids...

22 July 2024 5,492 6 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

MDCI module in Orca software?

Dear Researchers, My question is associated with the "MDCI" method in Orca. Please let me clarify my question using a simple example: Suppose we are going to perform CBS extrapolation using "!...

21 July 2024 1,632 0 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View

What are the principles of physical chemistry?

what are the main points

10 July 2024 9,236 5 View

Vidhura Mahendra

Hi Shan,

There is a good article on photo-stability of HDPE that you may can be useful worth looking at. Attached is the link for you.

http://www.jeffjournal.org/papers/Volume8/JEFF8-01-07.B.Butola.pdf

Emmanuel Richaud

you can review the " plastics additives handbook" (ed: H. Zweifel)

regards

Jousheed Pk

You can add dibenzoyl methane for UV stabilization. It is good UV stabilizer for plastics, especially for PVC, PE, PP etc.