Submit papers to 5th Int Conf on Informatics, Electronics & Vision (ICIEV), 13-14 May, 2016, BD http://cennser.org/iciev - Tech CoSponsor IEEE CompSoc

31 December 2015 9,508 0 View

Are you joining 4th Intl Conf on Informatics, Electronics & Vision (ICIEV), 2015, Japan http://cennser.org/iciev ?

Pls share the call for paper

10 November 2014 4,278 1 View

Call for Paper: Int Conf on Env Aspects of BD n the World

Dear Sir, Please submit your work and attend the 2nd ICEAB, Uni of Kitakyushu, Japan, 10-11 Sept. 2011: Visit http://benjapan.org/iceab For any query, please mail to atiqahad @ yahoo. com...

11 December 2010 1,006 1 View

Call for Paper: Int Conf on Env Aspects of BD n the World

Dear Sir, Please submit your work and attend the 2nd ICEAB, Uni of Kitakyushu, Japan, 10-11 Sept. 2011: Visit http://benjapan.org/iceab For any query, please mail to atiqahad @ yahoo. com...

11 December 2010 1,779 2 View

Call for Paper: Int Conf on Env Aspects of BD n the World

Dear Sir, Please submit your work and attend the 2nd ICEAB, Uni of Kitakyushu, Japan, 10-11 Sept. 2011: Visit http://benjapan.org/iceab For any query, please mail to atiqahad @ yahoo. com...

11 December 2010 8,850 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is your perception on using visual analysis or quantitative approaches to evaluate data from single-case research designs (n of 1 trials)?

Results of single-case research designs (i.e., n-of-1 trials) are often evaluated by visually inspecting the time-series graph and computing quantitative indices. A question our research team is...

03 March 2021 687 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

No title

02 March 2021 324 2 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

What is the value of Conference Review Paper?

How much value does a review paper carry in a higher study aspirant student's profile which is presented in a Peer Reviewed Scopus Indexed conference?

27 February 2021 2,068 3 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View