Hello,
I am looking for PDMS membrane for propylene glycol and glycerol separation. I would highly appreciate if someone could recommend a supplier.
Thank you
Hripsime
Dear Hripsime,
You might contact these two suppliers
1-Interstate Specialty Products Supplies PDMS Sheets and Membranes
Contacts
Interstate Specialty Products
Abigail Smalley, 800-984-1811
[email protected]
2-Specialty Silicone Products, Inc.
Corporate Technology Park
3 McCrea Hill Road
Ballston Spa, NY 12020
Toll Free: 800-437-1442
Phone: 518-885-8826
Fax: 518-885-4682
Good luck,
Rafik
hello Hripsime,
You can fabricate your own PDMS membrane using PDMS solution by spin coating method.
http://link.springer.com/article/10.1007/s10544-007-9070-6
with regards,
Dear Rafik and Prasoon,
Thank you very much for your kind replies. Much appreciated.
Best regards
One more
Telephone 01376 330033
Fax 01376 339163
Email [email protected]
Shielding Solutions Ltd
410 Avenue West
Skyline 120
Great Notley
Essex
CM77 7AA
Hi,
you can check these companies
SolSep (Apeldoorn, Netherlands), Pervatech (Rijssen, Netherlands), Sulzer Chemtech (Neunkirchen, Germany), and Celanese (NC, United States). Membrane Technology and Research, (MTR) (CA, United States)
two more:
Sulzer Chemtech (Switzerland) and PolyAn GmbH (Germany)
Dear all,
PDMS coated on PAN porous support . It's a commercial membrane by Sulzer (DeltaMem) new name.may be also check all Pervaporation companies.
One more:
Greene Rubber Co.
Also Elveflow sells a "PDMS membrane station" for making your own membranes (they claim reproducible thickness, 1µm to 250µm), they also probably have technical insights to offer.
I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...
03 March 2021 4,116 4 View
Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !
02 March 2021 5,785 3 View
Incompletely cross-linked pdms are difficult to remove.
01 March 2021 798 3 View
Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...
28 February 2021 7,882 2 View
I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...
28 February 2021 298 3 View
I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...
27 February 2021 4,218 7 View
I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...
25 February 2021 2,615 3 View
What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?
24 February 2021 8,219 2 View
I want to remove PDMS oligomers from the surface of nanolayers. I have just read a very helpful paper about the compatibility of PDMS with different solvents( Solvent Compatibility of...
24 February 2021 7,845 5 View
I am a Master student in Biomedical (Bio-electrical) Engineering and work on " 2D-3D registration ( CT and X-Ray) as my thesis. I created DRR from CT and want use CNN( Convolutional Neural...
19 February 2021 6,354 3 View