What type of vapourization will teflon exhibit when it is ablated in PPT? How can it be controlled?

More Julin J B's questions See All

Ethylene glycol is newtonian or non newtonian fluid?

Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.

09 August 2024 2,111 2 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

Can any of you suggest how to find the detection limit.?

I am working on flourescence sensing of heavy metals using quantum dots.Can any of you suggest how to find the detection limit. Whether it is calculated from formula or we can get from instrument?

19 July 2024 7,411 3 View

Dear researchers. pl help how to plot jablonski energy level graph and magnetic hysteresis curve in origin?

through origin software

17 July 2024 4,991 0 View

Cloning of flaviviruses is difficult i have noticed that cells loose their transformation ability after cloning fragments inside vector any advice?

As flaviviruses genome is very frequently prone to mutation hence it is very difficult to clone whole genome inside vector what kind of vector and cells can sustain such amount of cloning...

11 July 2024 4,284 0 View

I am not getting proper colonies while ligating one of fragments in my vector the colonies seems to be normal but in light it seems lysed any reason?

I am working on cloning of a gene fragment inside my vector everything we tried to do correctly like making insert and vector with utmost care but after ligation the morphology of colonies seems...

11 July 2024 9,010 3 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View

I have a doubt in finding the amount of ferromagnetic and antiferromagnetic contribution in a canted system?

Is it possible to differentiate or calculate, the amount of ferromagnetic and antiferromagnetic contribution in a canted system? (Weakly frustrated canted antiferromagnetic system)

25 June 2024 6,210 0 View

How transmittance is dependent on the band gap and atomic structure?

UV-Visible NIR analysis

20 June 2024 9,056 3 View

Whether size obtained from TEM and XRD should be equal?

I have got crystalline size around 15nm from xrd but TEM is giving particle size 4nm

20 June 2024 6,064 8 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

Why do fish have fishy odors naturally ?

Chemical Engineering /Food Engineering

20 July 2024 4,152 4 View

How do you decide an optimal AC amplitude for non-faradaic electrochemical impedance spectroscopy?

I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...

16 July 2024 5,031 1 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

Oleg Nizhnik

Smooth vaporization (no pitting). Vaporization rate is nearly proportional to discharge power. Main vaporization/decomposition product is C2F4. See also:

http://deepblue.lib.umich.edu/bitstream/handle/2027.42/48908/d11118.pdf?sequence=2

Georges Duffa

C2F4 constitute the major part (>95%) of the decomposition of PTFE. It is possible to explain the ablation mechanism without introducing a vaporization law. This is explained in my book published by AIAA in the Educational Series recently.