What formula can I use to get BER and Q-factor similar to values got from optisystem?

15 May 2024 1 5K Report

I am doing a research on WDM using optisystem to get values for BER and q-factor. What formula can I use to get BER and Q-factor similar to values got from optisystem?

Haidar Sadeq Zaeer Dhaam

the formula should be related to your system

Badges
Science topic

More Winner Minah-Eeba's questions See All

How Do I apply Floquet boundary condition on two boundaries of a beam in Comsol?

Hello all, Good day. I just started a new project on metamaterials using a mechanical beam made of 3D printed PETG. My unit cell representing the repeated structure is about 50mm in length. I...

30 September 2019 3,889 8 View

How to choose parameters of filters in RoF system with low carrier frequencies (2.412 &2.484)?

I am using optisystem to simulate RoF system for two users at Wifi frequency using direct modulation and low data rate , but I could not get the result. I think the problem in some parameters of...

15 December 2020 4,353 1 View

How to implement optical CDMA using optisystem and matlab all together?

I want to implement CDMA in optisystem and using the coding in Matlab. Need clues and tips on how one can be able to achieve that. I'm required to co simulate the project both with Matlab and...

19 March 2020 1,455 6 View

Is there any new ideas for solving the RWA problem in all optical WDM networks?

A problem of fundamental importance in the design of all-optical WDM networks is "Routing and Wavelength Assignment (RWA)" problem, which depends on the light path route and wavelength selection...

09 February 2020 1,497 9 View

How to impliment "Reconfigurable All-Optical Logic Gates Using Single Semiconductor Optical Amplifier at 100-Gb/s" in optisystem?

optisystem block diagram for the above mentioned paper is required

09 October 2018 9,123 0 View

How to extract data from 3D Graph in Optisystem ?

i need to extract data from 3D plot in Optisystem, I need help

09 October 2018 4,145 0 View

How could we improve the fairness of connection requests in WDM optical networks?

The connection requests require different bandwidth/spectrum, and each having different path/route length. Could any one guide me...

08 September 2018 3,077 0 View

How to set user defined SNR and OSNR in Optisystem?

I need to simulate Optical Signal to Noise Ratio (OSNR) vs BER and SNR vs BER plot in Optisystem v.13. So, how can I define a custom SNR or OSNR for the same. What would be the appropriate way to...

09 October 2017 6,235 0 View

How the use of dual FSO channels using power splitter and combiner helpful and is it different from WDM of dual optical links?

Please also explain the difference of using Dual FSO channels in parallel and in series and how it is different from wavelength division multiplexing of optical links. And which one can be used...

08 October 2017 4,489 2 View

How to simulate an OTDR (optical time-domain reflectometer) in optisystem software?

I want to gain the fiber trace in optisystem software.How to simulate an OTDR (optical time-domain reflectometer) in optisystem software?Is there OTDR component in optisystem V.12.2 ?

08 September 2017 1,324 0 View

Are there open source Python codes to simulate Erbium doped fiber amplifier (EDFA)?

I currently use the tool OASIX 4.03 from OFS to simulate laser line power levels in a dense wavelength division multiplexing (DWDM) system. The tool is in a .exe file. But I need to integrate the...

07 August 2017 687 5 View