What is the relation between substrate thickness and reflection phase of FSS

I have another question regarding the relation between the thickness of the substrate and reflection phase of FSS.I have observed different results for different thickness i.e. the thickness of...

05 June 2017 2,149 1 View

Regarding bandwidth variation in TE and TM mode with angle of incidence in FSS structure

I have a question regarding the variation in the bandwidth of pass band FSS for oblique incidence in TE and TM mode. In TE mode I have observed the bandwidth decreases as the angle of incidence...

04 May 2017 2,342 1 View

How to extract the dispersion diagram from Eigenmode simulation data?

03 April 2016 4,503 0 View

What is your perception on using visual analysis or quantitative approaches to evaluate data from single-case research designs (n of 1 trials)?

Results of single-case research designs (i.e., n-of-1 trials) are often evaluated by visually inspecting the time-series graph and computing quantitative indices. A question our research team is...

03 March 2021 687 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

I have designed reflectarray element and feeding it though Horn Antenna on HFSS. After full wave simulation, I am not getting desired results?

I have designed reflectarray element to generate OAM beams at 5.8GHz and feeding it though Horn Antenna on HFSS. After full wave simulation, i am not getting desired results i.e Radiation pattern...

01 March 2021 9,701 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Microstrip antenna design tutorial of HFSS 3D layout module ?

I have designed a 24 GHz rectangular antenna on HFSS 3D model and got desired results while desing the same antenna with same dimensions I am getting resonance frequency at 27 GHz I am...

28 February 2021 4,426 2 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

How to approach CFD simulation results of a flow past a cylinder?

Hi all, I'm doing a transient simulation of flow past a rectangular cylinder close to the free surface. As far as I'm concerned, the common practice is to discard the initial stages of the...

25 February 2021 1,348 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What is the better software for approximation of 3D surface with equations?

I have a massive of x, y, z coordinates of 2D surface in 3D space, which builded in Ansys HFSS or AutoCAD. How can I get the analitical aproximation of this surface by formulas?

21 February 2021 3,444 7 View