Is there any method to couple latest version of SUMO with ns-2?

More Vaibhav Gulati's questions See All

Anyone familiar with MANET's changing sink implementation in ns2?

In MANETs, there are towers for a particular region and if we move out of range of a particular tower while moving we get connected to another tower. How to implement similar scenario in ns2 if a...

02 March 2015 7,528 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

I have designed reflectarray element and feeding it though Horn Antenna on HFSS. After full wave simulation, I am not getting desired results?

I have designed reflectarray element to generate OAM beams at 5.8GHz and feeding it though Horn Antenna on HFSS. After full wave simulation, i am not getting desired results i.e Radiation pattern...

01 March 2021 9,701 5 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Microstrip antenna design tutorial of HFSS 3D layout module ?

I have designed a 24 GHz rectangular antenna on HFSS 3D model and got desired results while desing the same antenna with same dimensions I am getting resonance frequency at 27 GHz I am...

28 February 2021 4,426 2 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How to replicate the well conditions of a crystal hit with 20%(w/v) isopropanol?

I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?

25 February 2021 9,761 1 View

What are the patterns of human behavior that lead to COVID-19 infections?

Does data from contact tracing help in establishing patterns of behavior and social interactions that lead to infections? There are cases here in the Philippines where patients have no travel...

25 February 2021 9,002 13 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Behnam Farhadi

sumo work only with ns-2.31

Vaibhav Gulati

and how to couple them ?

http://www.dlr.de/ts/en/Portaldata/16/Resources/sumo/sumo-doc-0.23.0.zip

also work with omnet++

http://veins.car2x.org/tutorial/#step4

Maurice José Khabbaz

Of course, you can simply run SUMO to generate the traffic traces and store them in a file. In a second step, you will import this file into your ns-2 simulation framework.