In RCC Slab, normally the blacksmith bind the main and distribution bars randomly with binding wire, approx. how much effect will it have on strength?
Also in beam, walls, etc., the same procedure is followed in many construction field.
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How to use ERP System in Global University ?
27 July 2024 8,229 0 View
here's a concise guide for preparing your CSV dataset in Excel to identify flood-triggering factors using an ANN: Clean and Format:Address missing values (fill with mean/median or remove if...
21 June 2024 7,941 0 View
how do integrate ECG, PCG, and clinical data to apply early fusion multimodal?
10 June 2024 3,289 1 View
I have performed the Molecular Docking using ADFR suite, I have obtained the files in _out.pdbqt format for ligand docked poses, upon inspection, both visually and reading the pdbqt files of...
08 June 2024 8,130 2 View
Dear Respected Scholars, I am working on detection of microplastic in prawn. Although, all the other parameters assessed smoothly but I have encounterd a problem during isolation of microplastics...
05 June 2024 2,469 0 View
In basin delineation and hydrological modeling, selecting the exact value in Flow Accumulation to identify streams is a critical step. The Flow Accumulation tool calculates the accumulated flow as...
30 May 2024 6,107 1 View
Are multi-level models appropriate for binary outcome variables for DHS datasets? If yes, what is the process?
30 May 2024 2,035 2 View
For my project, I need to extract RNA from muscle tissue of EEL. I am trying but the yield is low and Purity not good. The 260:230 ratio is always below 1.50 and 260:280 ratio ranges 1.6-1.86 and...
15 May 2024 3,024 2 View
For the design of three phase inverter for three phase motor drive, which is better using low DC voltage (12 V or 24 V DC) for the inverter stage then step it up using three phase transformer, or...
08 May 2024 3,491 3 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
How do you tie-break and rank these two in their strength?
03 August 2024 4,471 1 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,546 2 View
My research work is related to the calcination of limestone. I have a complex question and would like to consult with experts in this field. Could you please advise which kiln to choose (a...
18 July 2024 1,390 2 View
In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....
11 July 2024 4,476 3 View
In plant breeding research, line x tester mating designs are often used to assess gene action for various traits. Some studies suggest that the simultaneous significant mean squares for lines,...
30 June 2024 4,877 2 View
How to calculate Module Young from compressive strength and strain curve
29 June 2024 817 3 View
Hello everyone, without going too much into details, my thesis is about improving the bonding strength at the wire bonding process. I should focus on laser pretreatment of the substrate. Has...
17 June 2024 366 1 View
Cross-slip, twinning and fracture are major deformation modes adopted by loaded materials. It appears sound that these apparently different deformation mechanisms can be analysed on the equal manner!
15 June 2024 8,477 3 View
Recently I have an assignment about Simulating magnetic field and I will need the result to derive it. But when i downloaded it i noticed that i am just a new to Simulation software. So can anyone...
04 June 2024 1,270 0 View