I am doing research in field of statistics.
I am doing an impact analysis of bullet on a plate. But for that simulation, I require orthotropic properties of materials like PPS and PEEK which are Unidirectional type. How to find them?...
16 February 2021 8,775 2 View
I want to do analysis in the ANSYS ACP module. For the same, I am trying to insert Properties of material in which I need to add Isotropic Elasticity ,orthotropic stress limit and Ply Type. But If...
30 January 2021 4,438 3 View
Hello all, Im Ajinkya. Doing analysis of High velocity bullet on plate made of 3 different materials from 10m distance. In which software it will be good for analysis ANSYS or LSDYNA or ABAQUS?
04 January 2021 9,462 4 View
Is there any reasons for not using two oxides for hybrid nanofluids??
12 August 2019 9,710 4 View
How Glow Discharge Spectroscopy can be used to characterize surface oxide films formed in hot rolling? What are its detection limits for various elements? Can it detect low atomic weight elements...
19 January 2015 5,875 1 View
01 January 1970 5,044 3 View
http://www.webology.org/2016/v13n1/editorial21.pdf
01 January 1970 4,963 4 View
Answered By: Laurissa GannLast Updated: Feb 28, 2018 Views: 99 There are several ways to measure the impact of a single article. Traditionally, authors have relied on citation counts. However,...
01 January 1970 586 6 View
Indian academic institutions have been in denial about plagiarism. There is a certain stock of unconvincing justifications given to excuse the practice. in India will, sooner rather than later,...
01 January 1970 6,704 8 View
01 January 1970 9,004 2 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...
28 February 2021 400 1 View
Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks
24 February 2021 9,378 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...
24 February 2021 1,598 2 View
Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...
23 February 2021 1,761 1 View
Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...
22 February 2021 4,882 3 View
For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...
21 February 2021 7,624 3 View
Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...
21 February 2021 2,333 4 View
I need to simulate the optical properties of a biomaterial, namely DNA, in COMSOL. Basically I need to simulate the IR absorption spectrum of a cylinder filled with a 'concentration' of DNA. I am...
21 February 2021 3,043 3 View
