How to calculate refractive index (n and kvalue) against energy (in eV) data for alloyed nanomaterials through Independent Phase Approximation method?

Suggest me the method or some other software to calculate the above said data for nanoparticles.

21 February 2021 3,350 7 View

What the error mean square (in a split plot design) is always higher for the main plot error as compared to the sub plot error ?

I know that in split plot design the main plot error is larger than the sub plot error. There is more error degree of freedom for sub plot as compared to main plot. But, in statistical analysis,...

14 December 2020 6,669 4 View

How can we make better contacts on thin films for I-V measurement?

Dear researchers, I am currently trying to perform I-V measurements for thin films. Could anybody let me know what is the best way to perform I-V measurements using Keithley 2600. How to make...

01 December 2020 9,103 9 View

Which are the best methods used for isolation and purification of plant pathogenic fungi and bacteria ?

Best methods suitable for isolation and purification of plant pathogenic fungi and bacteria from plant and soil samples....Latest methods....Any special advantages....Procedure to be followed...etc.

28 November 2020 3,365 3 View

How health psychology is helpful to deal the daily life issues?

Psychological Impact of Health Disease on Human Behaviour. If anybody is interested they can join us.

10 August 2020 8,007 13 View

Does plasma therapy works for treatment of covid-19?

04 August 2020 8,186 11 View

I am looking for an open source seismic hazard and risk analysis software. Is there any software available free of cost?

Open source and easy to learn with proper documentation.

26 April 2020 4,994 2 View

In ansys CFD, simulation, Can we initialize two fluids kept in two adjacent compartment with two different temperatures?

Compartment wall temperature can easily initialzed with boundary conditions but if fluid inside it are at different temperatures?

03 February 2020 4,495 4 View

In Ansys CFD can we assign cell zone temperature conditions along with existing fluid/solid material conditions?

Cell zone conditions are about assigning a particular fluid or solid inside it, but it does not allow hot or cold conditions of fluid inside it. can we assign them in Ansys CFD simulation?

03 February 2020 5,199 4 View

How do we determine the position and orientation of a moving robot ??

How do we determine the position and orientation of a moving robot using IMU sensors such as MPU6050 or MPU9250 (i.e. accelerometer , gyroscope and magnetometer sensor data)??? kindly advise...

22 November 2019 7,825 5 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

How can the modification of garden soil cause global warming?

Hello, I am working on a soil project and I found a primary research article that tests how the modification of agricultural soil can cause global warming, using a thermal collector, however I...

02 March 2021 7,161 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View