Hello
I need to model on Simulink a vertical wind turbine connected to an AC bus.
Can anyone help me ?
Hello,
Here you may get some ideas on how to model an AC vertical wind turbine.
https://kr.mathworks.com/matlabcentral/fileexchange/46909-vawt-analysis
Regards
There are quite a number of nice works, like:
https://ieeexplore.ieee.org/abstract/document/849122/
or
https://ieeexplore.ieee.org/abstract/document/1597345/
check this link
I'm working on a cross sectional study ,if I selected to use published survey about medication adherence in my thesis (already validated and has high reliability),but this study did not follow any...
23 April 2022 5,214 0 View
I am totally new to phage. The project I'm working on is about a prophage. When I use mitomycin C to induce bacteria lytic cycle I found there are several kinds of plaque(if sorted by size, see...
30 September 2020 547 3 View
We are trying to desalt a digest from an IP that has been separated by SDS-PAGE and ingel digested with trypsin (essentially as in Shevchenko et al. 2006). We make stagetips essentially by the...
08 April 2019 4,580 13 View
The easy answer I kind of already know, yes. I learned that the main differences between wireless unicast, multicast and broadcast lies in the encryption section. Correct me if I am wrong, but I...
03 October 2018 4,641 3 View
Hello I want to modelize a renewable grid with PV, battery and loads all connected to an AC bus. I have the PV but for the battery I need to design a bidirectional DC/DC-DC/AC converter in order...
10 September 2018 5,205 3 View
As a mathematician trying to understand the way the Signal-To-Noise ratio works in Digital Signal Processing, I have the following observation: A signal is recorded, suppose I recorded a class...
17 January 2018 9,357 10 View
I have always done an nMDS plot and then moved onto my ANOSIM, but I am actually unsure as to why its this order? Is the nMDS plot need to have good stress to be able to do my ANOSIM? And do I...
01 November 2015 4,776 3 View
Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...
11 August 2024 8,141 3 View
I am analyzing cherts from different sources found within one specific geologic formation using ICP-MS/ES. My committee was asking this question about my analysis. I was not sure how to answer this
05 August 2024 7,902 3 View
I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from experts in the field. If you are an expert or researcher working on...
02 August 2024 2,627 1 View
I want to know that n-doped side of solar cell is connected with positive or negative electrode.
20 July 2024 1,348 2 View
I studying PhD course in Urban design for Health. I need to know in some fileds: residental block, green open space and Transport TOD. I need connect with expert in that fileds.
14 July 2024 1,892 3 View
I have a Simulink model that connected a main utility (AC-grid) with a three-phase load changing from 20kW to 100kW in 5 seconds and I don't know how to build this load in Simulink. Please your...
14 July 2024 8,892 3 View
"Today several adjectival phrases have been used to describe English like ‘International Language’, ‘Lingua-Franca’, ‘Language for Globally Connecting’, ‘Library Language’, ‘Official Language’,...
01 July 2024 8,406 5 View
Sharing research simultaneously on both platforms
28 June 2024 9,120 2 View
I use LoRa with Matlab/Simulink
23 June 2024 3,847 3 View
Hi, I am looking to link MATLAB to Aspen Adsorption. I know that for Aspen Plus, it is possible to use actxserver(). Does anyone know if the same method can be used for Aspen Adsorption as well?...
20 June 2024 8,338 2 View