How to find the specific heat for nano fluids?

More Jeryrajkumar Lucas's questions See All

How to calculate the volume of air that can be stored in a compressed tank? Is it possible to calculate bar??

thank you in advance

01 February 2018 8,109 0 View

How to calibrate slip gauges?

Read 3 answers by scientists with 3 recommendations from their colleagues to the question asked by Jeryrajkumar Lucas on Aug 3, 2017

07 August 2017 503 3 View

How many words should be in the abstract?

Read 9 answers by scientists with 1 recommendation from their colleagues to the question asked by Jeryrajkumar Lucas on Jul 20, 2017

06 July 2017 2,785 9 View

What is the difference between fermions and bosons?

Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.

04 May 2017 7,499 0 View

What happens if gasoline is used in a Diesel engine?Diesel engine will work ?

Read 1 answer by scientists to the question asked by Jeryrajkumar Lucas on May 24, 2017

04 May 2017 3,972 1 View

Anything faster than light?

Read 1 answer by scientists to the question asked by Jeryrajkumar Lucas on Apr 7, 2017

03 April 2017 6,551 1 View

Why do self-employed?

01 February 2017 3,262 1 View

What are the NOx formation mechanisms are available during the combustion in IC engines?

I want to know about the NOx formation mechanisms and control methods.

01 February 2017 9,270 1 View

Why aircraft needs load sheet?

I want the reasons for load sheet in aircrafts.

01 February 2017 1,966 0 View

How do I test the prototype of fins for automobile( two wheeler) engine and what is the procedure for setup?

For my new project i want to change the fins which was existing in automobiles( two wheelers) l have done fins analysis in FLUENT. I want to test the prototype. tell me how to test the prototype...

01 February 2017 3,440 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

What is Nano technology with coronavirus helpe the human..and is it nano mterals removal of covid19?

I anwar by adsorption or reaction ..but it is either more method...

02 March 2021 4,811 2 View

How to compare different concentrations of nanoparticles for characterization from ICP-MS?

I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...

02 March 2021 7,626 1 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

Ghassan Fadhil Smaisim Popular answer

Dear sir,

You can read my paper about the nano fluid, I have here an experimental work and numerical work

( ANSYS and ANN). If you have any question, please you can ask me later.

Article Enhancement Heat Transfer of Cu-Water Nanofluids with Thermo...

Good luck

Ghassan Fadhil Smaisim